PANic ! im shaking, need help with last few steps in LIVE root context

im noooobie and made it all this way andis getting iffy on the last commands for root device ^ boot device … … i know their each name and rootpath

dev/nvme0n1p1 has the efi&boot flags

dev/nvme0n1p2 is the main disk root

i dont know if i need to put > export EFI_arch=x86_64

/configure /with-platform=efi --target= ${EFI_ARCH --program-prefix=“”

i couldnt beleive at it all when i finally got the commands to t0not give me SYNTAX ERROr all the time

and then this far…I think i got i t right and am USER=$ right now

it all went straight to heck when i was trying to get protonVPN working but i can=t say exactly when UEFI got switched to the fake one i have now tht claims secure boot is enabled and where i can only put in user password … i have the supervisor passsword but cant get to it its all grayed out blocked

my kernel is probably gone too but i dont know anything about that and how its done … this getting my system somewhat backhas taken the whole day

so thats it for my presentation > :sweat_smile:

anyone who can point me in the right direction please ?

you can boot on USB live manjaro ?
open a terminal and report

 inxi -Fza 

thats how i got back here in live context … im very unsure right now …

you boot on USB live manjaro ,
you launch firefox on this topic
and you open a terminal to copy / paste results

have to try to rebuild grub ?

Welcome to the forum! :wave:

Please post your system info as @stephane mentioned which is outlined here:

Please also see the following and edit your topic title and first post accordingly:

yeah i i guess so Im just hoping to get my bios back … i went trough like all of them commands that show that you are you and the “hijackers” gets exposed

rebuild the grub how do i actually do that … can you explan what it actualy is, to me it is like the terminal but more under the hood and pretty strangew …i never programmed anything but amateurishly saved a few computersby googling an trying

Thanks and im going to set my self down and look at what to do and not …

heres what terminal spat out on my setup … its in bad shape

    serial: <filter> rev: 1100 scheme: MBR
  SMART Message: Unknown USB bridge. Flash drive/Unsupported enclosure?
  Message: No optical or floppy data found.
  ID-1: /run/media/manjaro/Ventoy raw-size: 59.72 GiB size: 59.72 GiB (100.00%)
    used: 1.93 GiB (3.2%) fs: exfat dev: /dev/sdb1 maj-min: 8:17 label: Ventoy
    uuid: 23ED-282E
  Alert: No swap data was found.
  ID-1: /dev/nvme0n1p1 maj-min: 259:1 size: 300 MiB fs: vfat label: N/A
    uuid: 2012-66BF
  ID-2: /dev/nvme0n1p2 maj-min: 259:2 size: 238.17 GiB fs: ext4 label: N/A
    uuid: 45d69b80-421f-4f5d-ad6b-be1d10c003f0
  ID-3: /dev/sdb2 maj-min: 8:18 size: 32 MiB fs: vfat label: VTOYEFI
    uuid: B228-8EFB
  Hub-1: 1-0:1 info: Hi-speed hub with single TT ports: 16 rev: 2.0
    speed: 480 Mb/s chip-ID: 1d6b:0002 class-ID: 0900
  Device-1: 1-6:3 info: Areson Corp Laser mouse type: Mouse,HID
    driver: hid-generic,usbhid interfaces: 3 rev: 1.1 speed: 12 Mb/s power: 100mA
    chip-ID: 25a7:2410 class-ID: 0300
  Device-2: 1-10:4 info: Realtek RTS5129 Card Reader Controller
    type: <vendor specific> driver: rtsx_usb,rtsx_usb_ms,rtsx_usb_sdmmc
    interfaces: 1 rev: 2.0 speed: 480 Mb/s power: 500mA chip-ID: 0bda:0129
    class-ID: ff00 serial: <filter>
  Device-3: 1-11:5 info: Elan Micro ELAN:Fingerprint type: <vendor specific>
    driver: N/A interfaces: 1 rev: 2.0 speed: 12 Mb/s power: 100mA
    chip-ID: 04f3:0c03 class-ID: 0000
  Device-4: 1-12:6 info: Logitech Unifying Receiver type: Keyboard,Mouse,HID
    driver: logitech-djreceiver,usbhid interfaces: 3 rev: 2.0 speed: 12 Mb/s
    power: 98mA chip-ID: 046d:c52b class-ID: 0300
  Hub-2: 2-0:1 info: Super-speed hub ports: 8 rev: 3.0 speed: 5 Gb/s
    chip-ID: 1d6b:0003 class-ID: 0900
  Device-1: 2-2:2 info: Silicon Motion - Taiwan (formerly Feiya ) Flash Drive
    type: Mass Storage driver: usb-storage interfaces: 1 rev: 3.1 speed: 5 Gb/s
    power: 304mA chip-ID: 090c:1000 class-ID: 0806 serial: <filter>
  System Temperatures: cpu: 53.0 C pch: 54.0 C mobo: N/A
  Fan Speeds (RPM): N/A
  Processes: 245 Uptime: 7h 9m wakeups: 35 Init: systemd v: 252
  default: graphical tool: systemctl Compilers: gcc: 12.2.0 clang: 14.0.6
  Packages: pm: pacman pkgs: 1278 libs: 299 tools: gnome-software,pamac
  pm: flatpak pkgs: 0 Shell: Zsh v: 5.9 running-in: gnome-terminal inxi: 3.3.24

Now im ready to execute all i put in terminal … can i get some help with that :nerd_face:

im exhausted, been on this over 12 hours

@cirp Did you get lost? I moved your post here where I think you meant to post it. :wink:

haha jeeez thanks , where did i post only straight to you or what _???

maybe you like to look at the mess im tryin to get rollin and maybe STRONGLY advice against it or something like tha

The backtick sign is way for americans … if it wasnt just today when i have my keyboard altered for grub commanding wouldve had to go ALT + 9 + 6 … well im just assuming youre mostly americans here

in your inxi -Fza report ,
missing part system , Machine , Graphics , Audio , Network , Drives