Small problem with printing

I have 3 computers with Manjaro and 1 printer via network.
One computer has a problem with printing:
after power off for some time (computer and printer) , the printer prints a page previously printed.
And then the page(s), I want to print.

  1. Please read this:
    How to provide good information
    and post some more information so we can see what’s really going on. Now we know the symptom of the disease, but we need some more probing to know where the origin lies… :grin:

  2. An inxi --admin --verbosity=7 --filter --no-host --width would be the minimum required information for us to be able to help you. (Personally Identifiable Information like serial numbers and MAC addresses will be filtered out by the above command)
    Also, please copy-paste that output in-between 3 backticks ``` at the beginning and end of the code/text.

  3. please also add the output of:

    lpstat -l

and specify which printer you’re talking about, how it’s connected, …


  1. inxi…:
  Kernel: 5.10.49-1-MANJARO x86_64 bits: 64 compiler: gcc 
  v: 11.1.0 
  parameters: BOOT_IMAGE=/vmlinuz-5.10-x86_64 
  root=UUID=17504c02-341a-4e15-aa4f-f7cb98b282f9 ro quiet 
  Desktop: Xfce 4.16.0 tk: Gtk 3.24.29 info: xfce4-panel 
  wm: xfwm 4.16.1 vt: 7 dm: LightDM 1.30.0 Distro: Manjaro Linux 
  base: Arch Linux 
  Type: Desktop Mobo: Gigabyte model: J3455N-D3H serial: N/A 
  UEFI: American Megatrends v: F3 date: 11/16/2018 
  Message: No system battery data found. Is one present? 
  RAM: total: 7.62 GiB used: 1.56 GiB (20.5%) 
  Array-1: capacity: 16 GiB slots: 2 EC: None 
  max-module-size: 8 GiB note: est. 
  Device-1: ChannelA-DIMM0 size: 4 GiB speed: 1866 MT/s 
  type: DDR3 detail: synchronous bus-width: 64 bits 
  total: 64 bits manufacturer: Kingston 
  part-no: KHX1866C11S3L/4G serial: <filter> 
  Device-2: ChannelA-DIMM1 size: 4 GiB speed: 1866 MT/s 
  type: DDR3 detail: synchronous bus-width: 64 bits 
  total: 64 bits manufacturer: Kingston 
  part-no: KHX1866C11S3L/4G serial: <filter> 
  Info: Quad Core model: Intel Celeron J3455 bits: 64 type: MCP 
  arch: Goldmont family: 6 model-id: 5C (92) stepping: 9 
  microcode: 44 cache: L1: 224 KiB L2: 1024 KiB bogomips: 11984 
  Speed: 865 MHz min/max: 800/2300 MHz base/boost: 1500/2400 
  volts: 1.2 V ext-clock: 100 MHz Core speeds (MHz): 1: 865 
  2: 837 3: 852 4: 842 
  Flags: 3dnowprefetch acpi aes aperfmperf apic arat 
  arch_capabilities arch_perfmon art bts cat_l2 clflush 
  clflushopt cmov constant_tsc cpuid cpuid_fault cx16 cx8 de 
  ds_cpl dtes64 dtherm dts ept ept_ad erms est flexpriority fpu 
  fsgsbase fxsr ht ibpb ibrs ida intel_pt lahf_lm lm mca mce 
  md_clear mmx monitor movbe mpx msr mtrr nonstop_tsc nopl nx 
  pae pat pbe pclmulqdq pdcm pdpe1gb pebs pge pln pni popcnt pse 
  pse36 pts rdrand rdseed rdt_a rdtscp rep_good sdbg sep sha_ni 
  smap smep ss sse sse2 sse4_1 sse4_2 ssse3 stibp syscall tm tm2 
  tpr_shadow tsc tsc_adjust tsc_deadline_timer tsc_known_freq 
  tsc_reliable vme vmx vnmi vpid x2apic xgetbv1 xsave xsavec 
  xsaveopt xsaves xtopology xtpr 
  Vulnerabilities: Type: itlb_multihit status: Not affected 
  Type: l1tf status: Not affected 
  Type: mds status: Not affected 
  Type: meltdown status: Not affected 
  Type: spec_store_bypass status: Not affected 
  Type: spectre_v1 mitigation: usercopy/swapgs barriers and 
  __user pointer sanitization 
  Type: spectre_v2 mitigation: Full generic retpoline, IBPB: 
  conditional, IBRS_FW, STIBP: disabled, RSB filling 
  Type: srbds status: Not affected 
  Type: tsx_async_abort status: Not affected 
  Device-1: Intel HD Graphics 500 driver: i915 v: kernel 
  bus-ID: 00:02.0 chip-ID: 8086:5a85 class-ID: 0300 
  Display: x11 server: X.Org 1.20.11 compositor: xfwm4 v: 4.16.1 
  driver: loaded: intel unloaded: modesetting 
  alternate: fbdev,vesa display-ID: :0.0 screens: 1 
  Screen-1: 0 s-res: 1280x1024 s-dpi: 96 
  s-size: 338x270mm (13.3x10.6") s-diag: 433mm (17") 
  Monitor-1: DP1 res: 1280x1024 hz: 85 dpi: 81 
  size: 400x300mm (15.7x11.8") diag: 500mm (19.7") 
  OpenGL: renderer: Mesa Intel HD Graphics 500 (APL 2) 
  v: 4.6 Mesa 21.1.4 direct render: Yes 
  Device-1: Intel Celeron N3350/Pentium N4200/Atom E3900 Series 
  Audio Cluster 
  vendor: Gigabyte driver: snd_hda_intel v: kernel 
  alternate: snd_soc_skl,snd_sof_pci bus-ID: 00:0e.0 
  chip-ID: 8086:5a98 class-ID: 0403 
  Sound Server-1: ALSA v: k5.10.49-1-MANJARO running: yes 
  Sound Server-2: JACK v: 0.125.0 running: no 
  Sound Server-3: PulseAudio v: 14.2 running: yes 
  Sound Server-4: PipeWire v: 0.3.31 running: no 
  Device-1: Realtek RTL8111/8168/8411 PCI Express Gigabit 
  vendor: Gigabyte driver: r8169 v: kernel port: d000 
  bus-ID: 03:00.0 chip-ID: 10ec:8168 class-ID: 0200 
  IF: enp3s0 state: up speed: 1000 Mbps duplex: full 
  mac: <filter> 
  IP v4: <filter> type: dynamic noprefixroute scope: global 
  broadcast: <filter> 
  IP v6: <filter> type: dynamic noprefixroute scope: global 
  IP v6: <filter> type: noprefixroute scope: link 
  Device-2: Realtek RTL8111/8168/8411 PCI Express Gigabit 
  vendor: Gigabyte driver: r8169 v: kernel port: c000 
  bus-ID: 04:00.0 chip-ID: 10ec:8168 class-ID: 0200 
  IF: enp4s0 state: down mac: <filter> 
  WAN IP: <filter> 
  Message: No bluetooth data found. 
  Message: No logical block device data found. 
  Message: No RAID data found. 
  Local Storage: total: 232.89 GiB used: 16.4 GiB (7.0%) 
  SMART Message: Required tool smartctl not installed. Check 
  ID-1: /dev/sda maj-min: 8:0 vendor: Samsung 
  model: SSD 860 EVO 250GB size: 232.89 GiB block-size: 
  physical: 512 B logical: 512 B speed: 6.0 Gb/s rotation: SSD 
  serial: <filter> rev: 4B6Q scheme: GPT 
  Message: No optical or floppy data found. 
  ID-1: / raw-size: 80 GiB size: 78.24 GiB (97.81%) 
  used: 14.5 GiB (18.5%) fs: ext4 block-size: 4096 B 
  dev: /dev/sda4 maj-min: 8:4 label: N/A 
  uuid: 17504c02-341a-4e15-aa4f-f7cb98b282f9 
  ID-2: /boot raw-size: 1024 MiB size: 975.9 MiB (95.30%) 
  used: 102.8 MiB (10.5%) fs: ext4 block-size: 4096 B 
  dev: /dev/sda2 maj-min: 8:2 label: N/A 
  uuid: 14c0fdfc-f085-4481-abb6-4ff653166d51 
  ID-3: /boot/efi raw-size: 300 MiB size: 299.4 MiB (99.80%) 
  used: 312 KiB (0.1%) fs: vfat block-size: 512 B dev: /dev/sda1 
  maj-min: 8:1 label: N/A uuid: 455A-E10E 
  ID-4: /home raw-size: 143.59 GiB size: 140.34 GiB (97.73%) 
  used: 1.79 GiB (1.3%) fs: ext4 block-size: 4096 B 
  dev: /dev/sda5 maj-min: 8:5 label: N/A 
  uuid: 006c6b1f-9203-46f1-b741-26a3f1e5f770 
  Kernel: swappiness: 60 (default) cache-pressure: 100 (default) 
  ID-1: swap-1 type: partition size: 8 GiB used: 0 KiB (0.0%) 
  priority: -2 dev: /dev/sda3 maj-min: 8:3 label: N/A 
  uuid: 5dc9e94e-03fa-4efa-b243-9302e6b6aa75 
  Message: No unmounted partitions found. 
  Hub-1: 1-0:1 info: Full speed (or root) Hub ports: 8 rev: 2.0 
  speed: 480 Mb/s chip-ID: 1d6b:0002 class-ID: 0900 
  Hub-2: 1-8:2 info: Genesys Logic Hub ports: 4 rev: 2.0 
  speed: 480 Mb/s power: 100mA chip-ID: 05e3:0608 class-ID: 0900 
  Device-1: 1-8.1:3 info: Cherry Strait 3.0 type: Keyboard,HID 
  driver: hid-generic,usbhid interfaces: 2 rev: 2.0 
  speed: 1.5 Mb/s power: 100mA chip-ID: 046a:0180 class-ID: 0300 
  Device-2: 1-8.2:4 info: Logitech G500 Laser Mouse 
  type: Mouse,HID driver: hid-generic,usbhid interfaces: 2 
  rev: 2.0 speed: 12 Mb/s power: 98mA chip-ID: 046d:c068 
  class-ID: 0300 serial: <filter> 
  Hub-3: 2-0:1 info: Full speed (or root) Hub ports: 7 rev: 3.0 
  speed: 5 Gb/s chip-ID: 1d6b:0003 class-ID: 0900 
  System Temperatures: cpu: 26.0 C mobo: N/A 
  Fan Speeds (RPM): N/A 
  Processes: 185 Uptime: 2m wakeups: 0 Init: systemd v: 248 
  tool: systemctl Compilers: gcc: N/A Packages: pacman: 1193 
  lib: 405 flatpak: 0 Shell: Bash (su) v: 5.1.8 
  running-in: xfce4-terminal inxi: 3.3.05 
  1. lpstat -l:
    gives no output

  2. The printer Kyocera P6230cdn is connected to a router (Gbit Lan).
    All other computers are connected to that router.

  1. Please go to System Settings
    Type prin
    Click Printers
    Click the offending printer
    Provide a screenshot like this:

Where can I find the printer settings in XFCE ?

I can only find the printer settings in CUPS.

Sorry! I’m on KDE and I though you were too:



This partially correct:

I have one computer with KDE and two computers with XFCE.

1 Like

The printer is listed in CUPS.

I have used the printer driver from the webside of Kyocera.