This started happening since last few updates. After I entered my LUKS password in the Plymouth prompt the system goes into black screen, can’t even switch to any TTY. However, if I press Esc immediately after entering the disk password, the system boots normally. This is so strange I don’t even know how to debug this. Any help will be appreciated.
I noticed this issue with Kernel 5.10, 5.11 & 5.12. I hybrid intel-nvidia graphics. I am using latest nvidia-prime driver from mhwd.
I had something similar recently. I noticed that if I unplug my second monitor, SDDM loads fine and I can proceed and plug it in back.
However, this is not necessarily the same issue.
Welcome to Manjaro!
Please read this:
How to provide good information
and post some more information so we can see what’s really going on. Now we know the symptom of the disease, but we need some more probing to know where the origin lies…
An inxi --admin --verbosity=7 --filter --no-host --width would be the minimum required information… (Personally Identifiable Information like serial numbers and MAC addresses will be filtered out by the above command)
Also, please copy-paste that output in-between 3 backticks ``` at the beginning and end of the code/text.
The relevant part of a journalctl --boot=0 --system when:
boot=-1 to get the previous boot)would be helpful as well
P.S. If you enter a bit more details in your profile, we can also see which Desktop Environment you’re using, which CPU/GPU or Kernel, … you have without typing it every time
Output of inxi is below. I have updated my profile as well.
System:
Kernel: 5.12.1-2-MANJARO x86_64 bits: 64 compiler: gcc v: 10.2.0
parameters: BOOT_IMAGE=/vmlinuz-5.12-x86_64
root=/dev/mapper/CryptVolumeGroup-Root rw
cryptdevice=UUID=d0c7eb55-9338-41ed-b28c-496ddc99365b:CryptLVM quiet splash
sysrq_always_enabled=1 net.ifnames=0 apparmor=1 intel_iommu=1
security=apparmor ec_sys.write_support=1 udev.log_priority=3
resume=/dev/disk/by-uuid/97897af4-a7ea-47b6-8db1-4745590b229e
Desktop: KDE Plasma 5.21.4 tk: Qt 5.15.2 wm: kwin_x11 vt: 1 dm: SDDM
Distro: Manjaro Linux base: Arch Linux
Machine:
Type: Laptop System: System76 product: Adder WS v: addw1 serial: <filter>
Mobo: System76 model: Adder WS v: addw1 serial: <filter> UEFI: INSYDE
v: 1.07.11-0 date: 06/20/2019
Battery:
ID-1: BAT0 charge: 58.5 Wh (100.0%) condition: 58.5/62.1 Wh (94.2%)
volts: 12.4 min: 10.9 model: Notebook BAT type: Li-ion serial: <filter>
status: Full
Memory:
RAM: total: 31.07 GiB used: 3.21 GiB (10.3%)
RAM Report: permissions: Unable to run dmidecode. Root privileges required.
CPU:
Info: 6-Core model: Intel Core i7-9750H bits: 64 type: MT MCP
arch: Kaby Lake note: check family: 6 model-id: 9E (158) stepping: A (10)
microcode: DE cache: L2: 12 MiB bogomips: 62431
Speed: 800 MHz min/max: 800/4500 MHz Core speeds (MHz): 1: 800 2: 4048
3: 3427 4: 2391 5: 1791 6: 1032 7: 857 8: 800 9: 1315 10: 800 11: 800
12: 800
Flags: 3dnowprefetch abm acpi adx aes aperfmperf apic arat arch_perfmon art
avx avx2 bmi1 bmi2 bts clflush clflushopt cmov constant_tsc cpuid
cpuid_fault cx16 cx8 de ds_cpl dtes64 dtherm dts epb ept ept_ad erms est
f16c flexpriority flush_l1d fma fpu fsgsbase fxsr ht hwp hwp_act_window
hwp_epp hwp_notify ibpb ibrs ida intel_pt invpcid invpcid_single lahf_lm lm
mca mce md_clear mmx monitor movbe mpx msr mtrr nonstop_tsc nopl nx pae pat
pbe pcid pclmulqdq pdcm pdpe1gb pebs pge pln pni popcnt pse pse36 pti pts
rdrand rdseed rdtscp rep_good sdbg sep sgx sgx_lc smap smep ss ssbd sse sse2
sse4_1 sse4_2 ssse3 stibp syscall tm tm2 tpr_shadow tsc tsc_adjust
tsc_deadline_timer vme vmx vnmi vpid x2apic xgetbv1 xsave xsavec xsaveopt
xsaves xtopology xtpr
Vulnerabilities: Type: itlb_multihit status: KVM: VMX disabled
Type: l1tf
mitigation: PTE Inversion; VMX: conditional cache flushes, SMT vulnerable
Type: mds mitigation: Clear CPU buffers; SMT vulnerable
Type: meltdown mitigation: PTI
Type: spec_store_bypass
mitigation: Speculative Store Bypass disabled via prctl and seccomp
Type: spectre_v1
mitigation: usercopy/swapgs barriers and __user pointer sanitization
Type: spectre_v2 mitigation: Full generic retpoline, IBPB: conditional,
IBRS_FW, STIBP: conditional, RSB filling
Type: srbds mitigation: Microcode
Type: tsx_async_abort status: Not affected
Graphics:
Device-1: Intel UHD Graphics 630 vendor: CLEVO/KAPOK driver: i915 v: kernel
bus-ID: 00:02.0 chip-ID: 8086:3e9b class-ID: 0300
Device-2: NVIDIA TU106M [GeForce RTX 2070 Mobile] vendor: CLEVO/KAPOK
driver: nvidia v: 465.27 alternate: nouveau,nvidia_drm bus-ID: 01:00.0
chip-ID: 10de:1f10 class-ID: 0300
Device-3: Acer BisonCam NB Pro type: USB driver: uvcvideo bus-ID: 1-9:4
chip-ID: 5986:9102 class-ID: 0e02
Display: x11 server: X.Org 1.20.11 compositor: kwin_x11 driver:
loaded: modesetting,nvidia display-ID: :0 screens: 1
Screen-1: 0 s-res: 3840x2160 s-dpi: 192 s-size: 508x285mm (20.0x11.2")
s-diag: 582mm (22.9")
Monitor-1: eDP-1 res: 3840x2160 hz: 60 dpi: 284 size: 344x194mm (13.5x7.6")
diag: 395mm (15.5")
OpenGL: renderer: Mesa Intel UHD Graphics 630 (CFL GT2) v: 4.6 Mesa 21.0.3
direct render: Yes
Audio:
Device-1: Intel Cannon Lake PCH cAVS vendor: CLEVO/KAPOK
driver: snd_hda_intel v: kernel alternate: snd_soc_skl,snd_sof_pci_intel_cnl
bus-ID: 00:1f.3 chip-ID: 8086:a348 class-ID: 0403
Sound Server-1: ALSA v: k5.12.1-2-MANJARO running: yes
Sound Server-2: sndio v: N/A running: no
Sound Server-3: JACK v: 0.125.0 running: no
Sound Server-4: PulseAudio v: 14.2 running: yes
Sound Server-5: PipeWire v: 0.3.26 running: no
Network:
Device-1: Intel Wireless-AC 9560 [Jefferson Peak] driver: iwlwifi v: kernel
port: 5000 bus-ID: 00:14.3 chip-ID: 8086:a370 class-ID: 0280
IF: wlan0 state: up mac: <filter>
IP v4: <filter> type: dynamic noprefixroute scope: global
broadcast: <filter>
IP v6: <filter> type: dynamic noprefixroute scope: global
IP v6: <filter> type: noprefixroute scope: link
Device-2: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet
vendor: CLEVO/KAPOK driver: r8169 v: kernel port: 3000 bus-ID: 72:00.0
chip-ID: 10ec:8168 class-ID: 0200
IF: eth0 state: down mac: <filter>
IF-ID-1: docker0 state: down mac: <filter>
IP v4: <filter> scope: global broadcast: <filter>
WAN IP: <filter>
Bluetooth:
Device-1: Intel Bluetooth 9460/9560 Jefferson Peak (JfP) type: USB
driver: btusb v: 0.8 bus-ID: 1-14:5 chip-ID: 8087:0aaa class-ID: e001
Report: bt-adapter ID: hci0 rfk-id: 0 state: down
bt-service: enabled,running rfk-block: hardware: no software: no
address: <filter>
Logical:
Message: Unable to run lvs. Root privileges required.
Device-1: CryptLVM maj-min: 254:0 type: LUKS dm: dm-0 size: 464.76 GiB
Components:
p-1: nvme1n1p3 maj-min: 259:4 size: 464.76 GiB
Device-2: Data_Drive maj-min: 254:5 type: LUKS dm: dm-5 size: 465.75 GiB
Components:
p-1: nvme0n1p1 maj-min: 259:5 size: 465.76 GiB
Device-3: Web_Drive maj-min: 254:4 type: LUKS dm: dm-4 size: 465.75 GiB
Components:
p-1: nvme0n1p2 maj-min: 259:6 size: 465.75 GiB
RAID:
Message: No RAID data found.
Drives:
Local Storage: total: 1.82 TiB used: 467.5 GiB (25.1%)
SMART Message: Unable to run smartctl. Root privileges required.
ID-1: /dev/nvme0n1 maj-min: 259:1 vendor: Samsung
model: SSD 970 EVO Plus 1TB size: 931.51 GiB block-size: physical: 512 B
logical: 512 B speed: 31.6 Gb/s lanes: 4 rotation: SSD serial: <filter>
rev: 2B2QEXM7 scheme: GPT
ID-2: /dev/nvme1n1 maj-min: 259:0 vendor: Samsung
model: SSD 970 EVO Plus 500GB size: 465.76 GiB block-size: physical: 512 B
logical: 512 B speed: 31.6 Gb/s lanes: 4 rotation: SSD serial: <filter>
rev: 2B2QEXM7 scheme: GPT
ID-3: /dev/sda maj-min: 8:0 vendor: Samsung model: SSD 850 EVO 500GB
size: 465.76 GiB block-size: physical: 512 B logical: 512 B speed: 6.0 Gb/s
rotation: SSD serial: <filter> rev: 1B6Q scheme: GPT
Message: No optical or floppy data found.
Partition:
ID-1: / raw-size: 160 GiB size: 160 GiB (100.00%) used: 46.67 GiB (29.2%)
fs: btrfs dev: /dev/dm-1 maj-min: 254:1 mapped: CryptVolumeGroup-Root
label: N/A uuid: N/A
ID-2: /boot raw-size: 512 MiB size: 511 MiB (99.80%) used: 265 MiB (51.9%)
fs: vfat dev: /dev/nvme1n1p2 maj-min: 259:3 label: N/A uuid: D740-2464
ID-3: /boot/efi raw-size: 512 MiB size: 511 MiB (99.80%)
used: 416 KiB (0.1%) fs: vfat dev: /dev/nvme1n1p1 maj-min: 259:2 label: N/A
uuid: D7CE-89F5
ID-4: /home raw-size: 272.76 GiB size: 272.76 GiB (100.00%)
used: 237.47 GiB (87.1%) fs: btrfs dev: /dev/dm-2 maj-min: 254:2
mapped: CryptVolumeGroup-Home label: N/A uuid: N/A
ID-5: /home/<filter>/data_drive raw-size: 465.75 GiB
size: 465.75 GiB (100.00%) used: 173.9 GiB (37.3%) fs: btrfs dev: /dev/dm-5
maj-min: 254:5 mapped: Data_Drive label: N/A uuid: N/A
ID-6: /home/<filter>/web_drive raw-size: 465.75 GiB
size: 465.75 GiB (100.00%) used: 9.21 GiB (2.0%) fs: btrfs dev: /dev/dm-4
maj-min: 254:4 mapped: Web_Drive label: N/A uuid: N/A
Swap:
Kernel: swappiness: 10 (default 60) cache-pressure: 50 (default 100)
ID-1: swap-1 type: partition size: 32 GiB used: 0 KiB (0.0%) priority: -2
dev: /dev/dm-3 maj-min: 254:3 mapped: CryptVolumeGroup-SWAP label: N/A
uuid: 97897af4-a7ea-47b6-8db1-4745590b229e
Unmounted:
ID-1: /dev/sda1 maj-min: 8:1 size: 529 MiB fs: ntfs label: Recovery
uuid: 2C58BB5058BB1792
ID-2: /dev/sda2 maj-min: 8:2 size: 100 MiB fs: vfat label: N/A
uuid: 38BB-55B2
ID-3: /dev/sda3 maj-min: 8:3 size: 16 MiB fs: <superuser required>
label: N/A uuid: N/A
ID-4: /dev/sda4 maj-min: 8:4 size: 128 GiB fs: bitlocker label: N/A
uuid: N/A
ID-5: /dev/sda5 maj-min: 8:5 size: 337.13 GiB fs: <superuser required>
label: N/A uuid: N/A
USB:
Hub-1: 1-0:1 info: Full speed (or root) Hub ports: 16 rev: 2.0
speed: 480 Mb/s chip-ID: 1d6b:0002 class-ID: 0900
Device-1: 1-6:2 info: Logitech Unifying Receiver type: Keyboard,Mouse,HID
driver: logitech-djreceiver,usbhid interfaces: 3 rev: 2.0 speed: 12 Mb/s
power: 98mA chip-ID: 046d:c52b class-ID: 0300
Device-2: 1-7:3 info: Synaptics type: <vendor specific> driver: N/A
interfaces: 1 rev: 2.0 speed: 12 Mb/s power: 100mA chip-ID: 06cb:00c7
class-ID: ff00 serial: <filter>
Device-3: 1-9:4 info: Acer BisonCam NB Pro type: Video driver: uvcvideo
interfaces: 2 rev: 2.0 speed: 480 Mb/s power: 500mA chip-ID: 5986:9102
class-ID: 0e02
Device-4: 1-14:5 info: Intel Bluetooth 9460/9560 Jefferson Peak (JfP)
type: Bluetooth driver: btusb interfaces: 2 rev: 2.0 speed: 12 Mb/s
power: 100mA chip-ID: 8087:0aaa class-ID: e001
Hub-2: 2-0:1 info: Full speed (or root) Hub ports: 8 rev: 3.1 speed: 10 Gb/s
chip-ID: 1d6b:0003 class-ID: 0900
Hub-3: 5-0:1 info: Full speed (or root) Hub ports: 2 rev: 2.0
speed: 480 Mb/s chip-ID: 1d6b:0002 class-ID: 0900
Hub-4: 6-0:1 info: Full speed (or root) Hub ports: 2 rev: 3.1 speed: 10 Gb/s
chip-ID: 1d6b:0003 class-ID: 0900
Sensors:
System Temperatures: cpu: 61.0 C mobo: N/A
Fan Speeds (RPM): N/A
Info:
Processes: 392 Uptime: 6m wakeups: 2 Init: systemd v: 247 tool: systemctl
Compilers: gcc: 10.2.0 alt: 4.9/4.9.4/8 clang: 11.1.0 Packages: 2526
pacman: 2507 lib: 563 flatpak: 10 snap: 9 Shell: Bash v: 5.1.4
running-in: yakuake inxi: 3.3.04
The journal log: Journal - Pastebin.com
You missed these bits:
If you don’t know which the relevant part is, please give me the time (up to a second) when the issue happens / doesn’t happen.
Thanks @Fabby , I will keep them in mind. Currently the problem seems to be resolved after after latest update.
This topic was automatically closed 15 days after the last reply. New replies are no longer allowed.