Manjaro Cinnamon Usb not working, not hardware problem, failed fixing attempt

Support
1

Hi,
My usb 3.0 prots weren’t working in Manjaro, but they work in Windows (dual boot config on laptop).
The laptop has 1 usb 2.0 and 2 usb 3.0 ports.

So I tried to fix it, and made it worse. Now usb 2.0 port is also not working. -_-

This is the link to the post I had open on my phone when trying to fix it:

TBH: I missread a lot and may have overlooked an important detail in the console output of the user in the post.

The following is a step by step command review of what stupid stuff I did with comments and output where I still have it.

State USB 3.0 not working and USB 2.0 Working
// for comments
# for console output I still have in hand
==============================================
lsmod | grep xhci
hwinfo --usb-ctrl
sudo modprobe xhci_pci xhci_pci_renesas

============================
USB 2.0 stopps working
===============
sudo modprobe xhci_pci_renesas xhci_pci
// trying to revert while thinking modprobe replaces x with y
reboot // trying to und the changes
hwinfo
hwinfo | grep "renesas"
sudo modprobe xhci_plat_hcd
sudo modprobe ehci-hcd
reboot // trying to und the changes
sudo pamac build hw-probe
// googled modprobe
sudo modprobe xhci_pci xhci_pci_renesas -r
// trying to get rid off stuff that made usb 2.0 not work 
hwinfo --usb-ctrl
sudo modprobe xhci_pci 
//following suggestion in hwinfo
sudo modprobe xhci_hcd
// trying commands from the forum post again
sudo modprobe ehci-hcd
sudo nano /etc/modules-load.d/usb3.conf
//looking for file in post result: empty nano => file doesn't exist or empty
lsusb -t
sudo inxi -Fazc0 --usb
==============
Starting to write this poste and trying to undo most modprobe commands by trying to remove the installed stuff
==============
sudo modprobe xhci_plat_hcd -r
sudo modprobe ehci-hcd -r
# modprobe: FATAL: Module ehci_hcd is buildin
sudo modprobe xhci-hcd -r
# modprobe: FATAL: Module xhci_hcd is builtin.
sudo modprobe xhci_hcd -r
# modprobe: FATAL: Module xhci_hcd is builtin.
sudo modprobe xhci_pci -r
sudo modprobe xhci_pci_renesas -r
sudo modprobe xhci_pci // hoping it was the default before
=====
result of all of it:
not only is usb 3.0 not working
usb 2.0 has stopped working
+ I know i should read more befor doing

Stuff that could be usefull:
inxi -zv8:

System:
  Kernel: 6.6.26-1-MANJARO arch: x86_64 bits: 64 compiler: gcc v: 13.2.1
    clocksource: tsc avail: hpet,acpi_pm
    parameters: BOOT_IMAGE=/boot/vmlinuz-6.6-x86_64
    root=UUID=fac3077d-c6ec-4ddd-8a21-214d4a3e9017 rw quiet apparmor=1
    security=apparmor udev.log_priority=3
  Desktop: Cinnamon v: 6.0.4 tk: GTK v: 3.24.41 wm: Muffin v: 6.0.1 tools:
    avail: cinnamon-screensaver vt: 7 dm: LightDM v: 1.32.0 Distro: Manjaro
    base: Arch Linux
Machine:
  Type: Laptop System: Acer product: Aspire A315-23 v: V1.21
    serial: <superuser required>
  Mobo: DL model: Lotus_DA v: V1.21 serial: <superuser required>
    part-nu: 0000000000000000 uuid: <superuser required> UEFI: Insyde v: 1.21
    date: 09/08/2022
Battery:
  ID-1: BAT1 charge: 16.3 Wh (62.2%) condition: 26.2/37.0 Wh (70.7%)
    volts: 7.4 min: 7.6 model: MURATA AP16M4J type: Li-ion serial: <filter>
    status: discharging
Memory:
  System RAM: total: 20 GiB available: 17.5 GiB used: 3.51 GiB (20.1%)
  Message: For most reliable report, use superuser + dmidecode.
  Array-1: capacity: 64 GiB slots: 2 modules: 2 EC: None
    max-module-size: 32 GiB note: est.
  Device-1: Channel-A DIMM 0 type: DDR4 detail: synchronous unbuffered
    (unregistered) size: 16 GiB speed: 2400 MT/s volts: note: check curr: 1
    min: 1 max: 1 width (bits): data: 64 total: 64 manufacturer: Crucial
    part-no: CT16G4SFD824A.M16FE serial: <filter>
  Device-2: Channel-B DIMM 0 type: DDR4 detail: synchronous unbuffered
    (unregistered) size: 4 GiB speed: spec: 2667 MT/s actual: 2400 MT/s volts:
    note: check curr: 1 min: 1 max: 1 width (bits): data: 64 total: 64
    manufacturer: Micron Technology part-no: 4ATF51264HZ-2G6E1 serial: N/A
PCI Slots:
  Permissions: Unable to run dmidecode. Root privileges required.
CPU:
  Info: model: AMD Ryzen 5 3500U with Radeon Vega Mobile Gfx bits: 64
    type: MT MCP arch: Zen/Zen+ note: check gen: 1 level: v3 note: check
    built: 2019 process: GF 12nm family: 0x17 (23) model-id: 0x18 (24)
    stepping: 1 microcode: 0x8108109
  Topology: cpus: 1x cores: 4 tpc: 2 threads: 8 smt: enabled cache:
    L1: 384 KiB desc: d-4x32 KiB; i-4x64 KiB L2: 2 MiB desc: 4x512 KiB L3: 4 MiB
    desc: 1x4 MiB
  Speed (MHz): avg: 1345 high: 2100 min/max: 1400/2100 boost: enabled
    scaling: driver: acpi-cpufreq governor: schedutil cores: 1: 1266 2: 2100
    3: 1205 4: 1223 5: 1222 6: 1241 7: 1264 8: 1239 bogomips: 33609
  Flags: 3dnowprefetch abm adx aes aperfmperf apic arat avic avx avx2 bmi1
    bmi2 bpext clflush clflushopt clzero cmov cmp_legacy constant_tsc cpb
    cpuid cr8_legacy cx16 cx8 de decodeassists extapic extd_apicid f16c
    flushbyasid fma fpu fsgsbase fxsr fxsr_opt ht hw_pstate ibpb irperf
    lahf_lm lbrv lm mca mce misalignsse mmx mmxext monitor movbe msr mtrr
    mwaitx nonstop_tsc nopl npt nrip_save nx osvw overflow_recov pae pat
    pausefilter pclmulqdq pdpe1gb perfctr_core perfctr_llc perfctr_nb
    pfthreshold pge pni popcnt pse pse36 rapl rdrand rdseed rdtscp rep_good
    sep sev sev_es sha_ni skinit smap smca smep ssbd sse sse2 sse4_1 sse4_2
    sse4a ssse3 succor svm svm_lock syscall tce topoext tsc tsc_scale
    v_vmsave_vmload vgif vmcb_clean vme vmmcall wdt xgetbv1 xsave xsavec
    xsaveerptr xsaveopt
  Vulnerabilities:
  Type: gather_data_sampling status: Not affected
  Type: itlb_multihit status: Not affected
  Type: l1tf status: Not affected
  Type: mds status: Not affected
  Type: meltdown status: Not affected
  Type: mmio_stale_data status: Not affected
  Type: reg_file_data_sampling status: Not affected
  Type: retbleed mitigation: untrained return thunk; SMT vulnerable
  Type: spec_rstack_overflow mitigation: Safe RET
  Type: spec_store_bypass mitigation: Speculative Store Bypass disabled via
    prctl
  Type: spectre_v1 mitigation: usercopy/swapgs barriers and __user pointer
    sanitization
  Type: spectre_v2 mitigation: Retpolines; IBPB: conditional; STIBP:
    disabled; RSB filling; PBRSB-eIBRS: Not affected; BHI: Not affected
  Type: srbds status: Not affected
  Type: tsx_async_abort status: Not affected
Graphics:
  Device-1: AMD Picasso/Raven 2 [Radeon Vega Series / Radeon Mobile Series]
    vendor: Acer Incorporated ALI driver: amdgpu v: kernel arch: GCN-5
    code: Vega process: GF 14nm built: 2017-20 pcie: gen: 3 speed: 8 GT/s
    lanes: 16 ports: active: eDP-1 empty: HDMI-A-1 bus-ID: 05:00.0
    chip-ID: 1002:15d8 class-ID: 0300 temp: 43.0 C
  Display: x11 server: X.org v: 1.21.1.12 with: Xwayland v: 23.2.6 driver:
    X: loaded: amdgpu unloaded: modesetting alternate: fbdev,vesa dri: radeonsi
    gpu: amdgpu display-ID: :0 screens: 1
  Screen-1: 0 s-res: 1920x1080 s-size: <missing: xdpyinfo>
  Monitor-1: eDP-1 mapped: eDP model: BOE Display 0x07cb built: 2018
    res: 1920x1080 hz: 60 dpi: 142 gamma: 1.2 chroma: red: x: 0.584 y: 0.361
    green: x: 0.353 y: 0.569 blue: x: 0.161 y: 0.129 white: x: 0.314 y: 0.329
    size: 344x193mm (13.54x7.6") diag: 394mm (15.5") ratio: 16:9
    modes: 1920x1080, 1680x1050, 1280x1024, 1440x900, 1280x800, 1280x720,
    1024x768, 800x600, 640x480
  API: EGL v: 1.5 hw: drv: amd radeonsi platforms: device: 0 drv: radeonsi
    device: 1 drv: swrast surfaceless: drv: radeonsi x11: drv: radeonsi
    inactive: gbm,wayland
  API: OpenGL v: 4.6 compat-v: 4.5 vendor: amd mesa v: 24.0.2-manjaro1.1
    glx-v: 1.4 direct-render: yes renderer: AMD Radeon Vega 8 Graphics
    (radeonsi raven LLVM 16.0.6 DRM 3.54 6.6.26-1-MANJARO)
    device-ID: 1002:15d8 memory: 1.95 GiB unified: no
Audio:
  Device-1: AMD Raven/Raven2/Fenghuang HDMI/DP Audio
    vendor: Acer Incorporated ALI driver: snd_hda_intel v: kernel pcie: gen: 3
    speed: 8 GT/s lanes: 16 bus-ID: 05:00.1 chip-ID: 1002:15de class-ID: 0403
  Device-2: AMD ACP/ACP3X/ACP6x Audio Coprocessor
    vendor: Acer Incorporated ALI driver: snd_pci_acp3x v: kernel
    alternate: snd_rn_pci_acp3x, snd_pci_acp5x, snd_pci_acp6x, snd_acp_pci,
    snd_rpl_pci_acp6x, snd_pci_ps, snd_sof_amd_renoir, snd_sof_amd_rembrandt,
    snd_sof_amd_vangogh pcie: gen: 3 speed: 8 GT/s lanes: 16 bus-ID: 05:00.5
    chip-ID: 1022:15e2 class-ID: 0480
  Device-3: AMD Family 17h/19h HD Audio vendor: Acer Incorporated ALI
    driver: snd_hda_intel v: kernel pcie: gen: 3 speed: 8 GT/s lanes: 16
    bus-ID: 05:00.6 chip-ID: 1022:15e3 class-ID: 0403
  API: ALSA v: k6.6.26-1-MANJARO status: kernel-api with: aoss
    type: oss-emulator tools: alsactl,alsamixer,amixer
  Server-1: JACK v: 1.9.22 status: off tools: N/A
  Server-2: PipeWire v: 1.0.3 status: off tools: pw-cli
  Server-3: PulseAudio v: 17.0 status: active with: pulseaudio-alsa
    type: plugin tools: pacat,pactl,pavucontrol
Network:
  Device-1: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter
    vendor: Lite-On driver: ath10k_pci v: kernel pcie: gen: 1 speed: 2.5 GT/s
    lanes: 1 bus-ID: 02:00.0 chip-ID: 168c:0042 class-ID: 0280
  IF: wlp2s0 state: up mac: <filter>
  IP v4: <filter> type: dynamic noprefixroute scope: global
    broadcast: <filter>
  IP v6: <filter> type: dynamic noprefixroute scope: global
  IP v6: <filter> type: noprefixroute scope: link
  Device-2: Realtek RTL8111/8168/8211/8411 PCI Express Gigabit Ethernet
    vendor: Acer Incorporated ALI RTL8111/8168/8411 driver: r8169 v: kernel
    pcie: speed: Unknown lanes: 63 link-max: gen: 6 speed: 64 GT/s port: 2000
    bus-ID: 03:00.0 chip-ID: 10ec:8168 class-ID: 0200
  IF: enp3s0 state: down mac: <filter>
  Info: services: NetworkManager,wpa_supplicant
  WAN IP: <filter>
Bluetooth:
  Message: No bluetooth data found.
Logical:
  Message: No logical block device data found.
RAID:
  Message: No RAID data found.
Drives:
  Local Storage: total: 953.87 GiB used: 108.58 GiB (11.4%)
  SMART Message: Required tool smartctl not installed. Check --recommends
  ID-1: /dev/nvme0n1 maj-min: 259:0 vendor: Western Digital model: PC SN530
    SDBPNPZ-1T00-1014 size: 953.87 GiB block-size: physical: 512 B
    logical: 512 B speed: 31.6 Gb/s lanes: 4 tech: SSD serial: <filter>
    fw-rev: 21103900 temp: 38.9 C scheme: GPT
  Message: No optical or floppy data found.
Partition:
  ID-1: / raw-size: 373.08 GiB size: 366.15 GiB (98.14%)
    used: 108.51 GiB (29.6%) fs: ext4 dev: /dev/nvme0n1p5 maj-min: 259:5
    label: N/A uuid: fac3077d-c6ec-4ddd-8a21-214d4a3e9017
  ID-2: /boot/efi raw-size: 100 MiB size: 96 MiB (96.00%)
    used: 70.8 MiB (73.8%) fs: vfat dev: /dev/nvme0n1p1 maj-min: 259:1
    label: ESP uuid: A07A-1812
Swap:
  Alert: No swap data was found.
Unmounted:
  ID-1: /dev/nvme0n1p2 maj-min: 259:2 size: 16 MiB fs: <superuser required>
    label: N/A uuid: N/A
  ID-2: /dev/nvme0n1p3 maj-min: 259:3 size: 579.68 GiB fs: ntfs label: Acer
    uuid: CEE27AA8E27A9505
  ID-3: /dev/nvme0n1p4 maj-min: 259:4 size: 1024 MiB fs: ntfs
    label: Recovery uuid: 8C967B97967B808E
USB:
  Hub-1: 1-0:1 info: hi-speed hub with single TT ports: 4 rev: 2.0
    speed: 480 Mb/s (57.2 MiB/s) lanes: 1 mode: 2.0 chip-ID: 1d6b:0002
    class-ID: 0900
  Hub-2: 2-0:1 info: super-speed hub ports: 4 rev: 3.1
    speed: 10 Gb/s (1.16 GiB/s) lanes: 1 mode: 3.2 gen-2x1 chip-ID: 1d6b:0003
    class-ID: 0900
  Hub-3: 3-0:1 info: hi-speed hub with single TT ports: 2 rev: 2.0
    speed: 480 Mb/s (57.2 MiB/s) lanes: 1 mode: 2.0 chip-ID: 1d6b:0002
    class-ID: 0900
  Hub-4: 4-0:1 info: super-speed hub ports: 1 rev: 3.1
    speed: 10 Gb/s (1.16 GiB/s) lanes: 1 mode: 3.2 gen-2x1 chip-ID: 1d6b:0003
    class-ID: 0900
Sensors:
  System Temperatures: cpu: 43.9 C mobo: N/A gpu: amdgpu temp: 43.0 C
  Fan Speeds (rpm): N/A
Repos:
  Packages: 1432 pm: pacman pkgs: 1417 libs: 368 tools: pamac,yay pm: flatpak
    pkgs: 15
  Active pacman repo servers in: /etc/pacman.d/mirrorlist
    1: https://mnvoip.mm.fcix.net/manjaro/stable/$repo/$arch
    2: https://repo.ialab.dsu.edu/manjaro/stable/$repo/$arch
    3: https://ftp.nluug.nl/pub/os/Linux/distr/manjaro/stable/$repo/$arch
    4: https://ftp.cc.uoc.gr/mirrors/linux/manjaro/stable/$repo/$arch
    5: https://ridgewireless.mm.fcix.net/manjaro/stable/$repo/$arch
    6: https://mirror.init7.net/manjaro/stable/$repo/$arch
    7: https://manjaro.ynh.ovh/stable/$repo/$arch
    8: https://mirror.funami.tech/manjaro/stable/$repo/$arch
    9: https://mirror.kku.ac.th/manjaro/stable/$repo/$arch
    10: https://mirrors.tuna.tsinghua.edu.cn/manjaro/stable/$repo/$arch
    11: https://mirror.xenyth.net/manjaro/stable/$repo/$arch
    12: https://muug.ca/mirror/manjaro/stable/$repo/$arch
    13: https://mirrors.xtom.de/manjaro/stable/$repo/$arch
    14: https://mirror.yandex.ru/mirrors/manjaro/stable/$repo/$arch
    15: https://ba.mirror.garr.it/mirrors/manjaro/stable/$repo/$arch
    16: https://mirrors.gigenet.com/manjaro/stable/$repo/$arch
    17: https://mirror.23m.com/manjaro/stable/$repo/$arch
    18: https://uvermont.mm.fcix.net/manjaro/stable/$repo/$arch
    19: https://coresite.mm.fcix.net/manjaro/stable/$repo/$arch
    20: http://ossmirror.mycloud.services/os/linux/manjaro/stable/$repo/$arch
    21: https://forksystems.mm.fcix.net/manjaro/stable/$repo/$arch
    22: https://mirror.csclub.uwaterloo.ca/manjaro/stable/$repo/$arch
    23: https://mirrors.dotsrc.org/manjaro/stable/$repo/$arch
    24: https://mirrors.sonic.net/manjaro/stable/$repo/$arch
    25: http://mirror.datacenter.by/pub/mirrors/manjaro/stable/$repo/$arch
    26: https://mirror.archlinux.tw/Manjaro/stable/$repo/$arch
    27: https://mirrors.ustc.edu.cn/manjaro/stable/$repo/$arch
    28: https://mirror.telepoint.bg/manjaro/stable/$repo/$arch
    29: http://manjaro.mirrors.theom.nz/manjaro/stable/$repo/$arch
    30: https://mirror.dkm.cz/manjaro/stable/$repo/$arch
    31: https://mirror.2degrees.nz/manjaro/stable/$repo/$arch
    32: https://mirrors.jlu.edu.cn/manjaro/stable/$repo/$arch
    33: https://ftp.caliu.cat/pub/distribucions/manjaro/stable/$repo/$arch
    34: https://mirror.aarnet.edu.au/pub/manjaro/stable/$repo/$arch
    35: https://mirrors.manjaro.org/repo/stable/$repo/$arch
    36: https://mirror.dc.uz/manjaro/stable/$repo/$arch
    37: https://mirror.ufam.edu.br/manjaro/stable/$repo/$arch
    38: http://mirror.fcix.net/manjaro/stable/$repo/$arch
    39: https://mirror.nju.edu.cn/manjaro/stable/$repo/$arch
    40: https://mirror.math.princeton.edu/pub/manjaro/stable/$repo/$arch
    41: https://mirror.netcologne.de/manjaro/stable/$repo/$arch
    42: http://ftp.belnet.be/mirrors/manjaro/repos/stable/$repo/$arch
    43: https://edgeuno-bog2.mm.fcix.net/manjaro/stable/$repo/$arch
    44: http://ftp.free.org/mirrors/repo.manjaro.org/repos/stable/$repo/$arch
    45: https://ftp.linux.org.tr/manjaro/stable/$repo/$arch
    46: https://mirror.bouwhuis.network/manjaro/stable/$repo/$arch
    47: https://ohioix.mm.fcix.net/manjaro/stable/$repo/$arch
    48: https://ftpmirror1.infania.net/mirror/manjaro/stable/$repo/$arch
    49: https://repos.silknet.com/manjaro/stable/$repo/$arch
    50: http://ftp.snt.utwente.nl/pub/linux/manjaro/stable/$repo/$arch
    51: http://ftp.tsukuba.wide.ad.jp/Linux/manjaro/stable/$repo/$arch
    52: https://www.mirrorservice.org/sites/repo.manjaro.org/repos/stable/$repo/$arch
    53: http://ftp.rz.tu-bs.de/pub/mirror/manjaro.org/repos/stable/$repo/$arch
    54: https://mirror.albony.xyz/manjaro/stable/$repo/$arch
    55: https://mirror.nyist.edu.cn/manjaro/stable/$repo/$arch
    56: https://codingflyboy.mm.fcix.net/manjaro/stable/$repo/$arch
    57: https://repo.iut.ac.ir/repo/manjaro/stable/$repo/$arch
    58: https://mirrors.sjtug.sjtu.edu.cn/manjaro/stable/$repo/$arch
    59: https://opencolo.mm.fcix.net/manjaro/stable/$repo/$arch
    60: http://ftp.uni-kl.de/pub/linux/manjaro/stable/$repo/$arch
    61: http://mirror.terrahost.no/linux/manjaro/stable/$repo/$arch
    62: https://quantum-mirror.hu/mirrors/pub/manjaro/stable/$repo/$arch
    63: https://mirror.alpix.eu/manjaro/stable/$repo/$arch
    64: https://mirrors2.manjaro.org/stable/$repo/$arch
    65: https://mirror.futureweb.be/manjaro/stable/$repo/$arch
    66: https://mirror.phoepsilonix.love/manjaro/stable/$repo/$arch
    67: https://irltoolkit.mm.fcix.net/manjaro/stable/$repo/$arch
    68: https://manjaro.c3sl.ufpr.br/stable/$repo/$arch
    69: https://mirrors.ft.uam.es/manjaro/stable/$repo/$arch
    70: https://mirrors.cicku.me/manjaro/stable/$repo/$arch
    71: https://manjaro.kyberorg.fi/stable/$repo/$arch
    72: https://ftp.halifax.rwth-aachen.de/manjaro/stable/$repo/$arch
    73: https://ct.mirror.garr.it/mirrors/manjaro/stable/$repo/$arch
    74: https://mirrors.xtom.jp/manjaro/stable/$repo/$arch
    75: https://gsl-syd.mm.fcix.net/manjaro/stable/$repo/$arch
    76: http://kartolo.sby.datautama.net.id/manjaro/stable/$repo/$arch
    77: https://fosszone.csd.auth.gr/manjaro/stable/$repo/$arch
    78: https://manjaro.mirror.liquidtelecom.com/stable/$repo/$arch
    79: https://manjaro.mirrors.lavatech.top/stable/$repo/$arch
    80: https://mirror.koddos.net/manjaro/stable/$repo/$arch
    81: http://ftp.tu-chemnitz.de/pub/linux/manjaro/stable/$repo/$arch
    82: https://mirrors.up.pt/pub/manjaro/stable/$repo/$arch
    83: https://mirror.vinehost.net/manjaro/stable/$repo/$arch
    84: https://ask4.mm.fcix.net/manjaro/stable/$repo/$arch
    85: https://manjaro.mirror.garr.it/manjaro/stable/$repo/$arch
    86: https://mirrors.pku.edu.cn/manjaro/stable/$repo/$arch
    87: https://linorg.usp.br/manjaro/stable/$repo/$arch
    88: https://mirror.truenetwork.ru/manjaro/stable/$repo/$arch
    89: https://mirrors.xtom.ee/manjaro/stable/$repo/$arch
    90: https://fastmirror.pp.ua/manjaro/stable/$repo/$arch
    91: https://manjaro.repo.cure.edu.uy/stable/$repo/$arch
    92: https://manjaro.kurdy.org/stable/$repo/$arch
    93: https://nnenix.mm.fcix.net/manjaro/stable/$repo/$arch
    94: http://manjaro.grena.ge/stable/$repo/$arch
    95: https://mirror.easyname.at/manjaro/stable/$repo/$arch
    96: https://southfront.mm.fcix.net/manjaro/stable/$repo/$arch
    97: https://nocix.mm.fcix.net/manjaro/stable/$repo/$arch
    98: https://ftp.gwdg.de/pub/linux/manjaro/stable/$repo/$arch
    99: https://mirrors.netix.net/manjaro/stable/$repo/$arch
    100: https://mirror.freedif.org/Manjaro/stable/$repo/$arch
    101: https://mirror.erickochen.nl/manjaro/stable/$repo/$arch
    102: https://ftp.lysator.liu.se/pub/manjaro/stable/$repo/$arch
    103: https://mirror.alwyzon.net/manjaro/stable/$repo/$arch
    104: https://manjarolinux-mirror.cloud.mu/stable/$repo/$arch
    105: http://ftp.riken.jp/Linux/manjaro/stable/$repo/$arch
    106: http://mirror.xeonbd.com/manjaro/stable/$repo/$arch
    107: https://manjaro.ipacct.com/manjaro/stable/$repo/$arch
    108: http://mirror.is.co.za/mirrors/manjaro.org/stable/$repo/$arch
    109: https://mirrors.nic.cz/manjaro/stable/$repo/$arch
    110: https://mirrors.ocf.berkeley.edu/manjaro/stable/$repo/$arch
    111: https://mirror1.sox.rs/manjaro/stable/$repo/$arch
    112: https://volico.mm.fcix.net/manjaro/stable/$repo/$arch
    113: https://mirror.it4i.cz/manjaro/stable/$repo/$arch
    114: https://manjaro.mirror.wearetriple.com/stable/$repo/$arch
    115: https://ftp.psnc.pl/linux/manjaro/stable/$repo/$arch
    116: https://mirror.ibakerserver.pt/manjaro/stable/$repo/$arch
    117: https://mirror.kamtv.ru/manjaro/stable/$repo/$arch
Processes:
  CPU top: 5 of 280
  1: cpu: 400% command: ps pid: 5637 mem: 4.22 MiB (0.0%)
  2: cpu: 14.5% command: firefox pid: 1769 mem: 521.4 MiB (2.9%)
  3: cpu: 5.8% command: cinnamon pid: 1489 mem: 259.2 MiB (1.4%)
  4: cpu: 4.7% command: Xorg pid: 875 mem: 172.0 MiB (0.9%)
  5: cpu: 4.4% command: firefox pid: 1989 mem: 228.9 MiB (1.2%)
  Memory top: 5 of 280
  1: mem: 521.4 MiB (2.9%) command: firefox pid: 1769 cpu: 14.5%
  2: mem: 450.0 MiB (2.5%) command: firefox pid: 3925 cpu: 4.0%
  3: mem: 359.3 MiB (2.0%) command: firefox pid: 2537 cpu: 1.5%
  4: mem: 293.0 MiB (1.6%) command: firefox pid: 2053 cpu: 0.7%
  5: mem: 279.6 MiB (1.5%) command: firefox pid: 2895 cpu: 2.3%
Info:
  Processes: 280 Power: uptime: 42m states: freeze,mem,disk suspend: deep
    avail: s2idle wakeups: 0 hibernate: platform avail: shutdown, reboot,
    suspend, test_resume image: 6.99 GiB services: csd-power,upowerd
    Init: systemd v: 255 default: graphical tool: systemctl
  Compilers: clang: 16.0.6 gcc: 13.2.1 Shell: Bash v: 5.2.26
    running-in: gnome-terminal inxi: 3.3.34

lsusb -t:

/:  Bus 001.Port 001: Dev 001, Class=root_hub, Driver=xhci_hcd/4p, 480M
/:  Bus 002.Port 001: Dev 001, Class=root_hub, Driver=xhci_hcd/4p, 10000M
/:  Bus 003.Port 001: Dev 001, Class=root_hub, Driver=xhci_hcd/2p, 480M
/:  Bus 004.Port 001: Dev 001, Class=root_hub, Driver=xhci_hcd/1p, 10000M

hwinfo --usb-ctrl

08: PCI 500.3: 0c03 USB Controller (XHCI)                       
  [Created at pci.386]
  Unique ID: pb96.Hv+FGJY1z80
  Parent ID: JZZT.N70T6T_iyf8
  SysFS ID: /devices/pci0000:00/0000:00:08.1/0000:05:00.3
  SysFS BusID: 0000:05:00.3
  Hardware Class: usb controller
  Model: "AMD Raven USB 3.1"
  Vendor: pci 0x1022 "AMD"
  Device: pci 0x15e0 "Raven USB 3.1"
  SubVendor: pci 0x1025 "Acer Incorporated [ALI]"
  SubDevice: pci 0x1456 
  Driver: "xhci_hcd"
  Driver Modules: "xhci_pci"
  Memory Range: 0xc0700000-0xc07fffff (rw,non-prefetchable)
  IRQ: 34 (no events)
  Module Alias: "pci:v00001022d000015E0sv00001025sd00001456bc0Csc03i30"
  Driver Info #0:
    Driver Status: xhci_pci is active
    Driver Activation Cmd: "modprobe xhci_pci"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #20 (PCI bridge)

21: PCI 500.4: 0c03 USB Controller (XHCI)
  [Created at pci.386]
  Unique ID: hwex.oJy+ktfkUX0
  Parent ID: JZZT.N70T6T_iyf8
  SysFS ID: /devices/pci0000:00/0000:00:08.1/0000:05:00.4
  SysFS BusID: 0000:05:00.4
  Hardware Class: usb controller
  Model: "AMD Raven USB 3.1"
  Vendor: pci 0x1022 "AMD"
  Device: pci 0x15e1 "Raven USB 3.1"
  SubVendor: pci 0x1025 "Acer Incorporated [ALI]"
  SubDevice: pci 0x1456 
  Driver: "xhci_hcd"
  Driver Modules: "xhci_pci"
  Memory Range: 0xc0600000-0xc06fffff (rw,non-prefetchable)
  IRQ: 43 (no events)
  Module Alias: "pci:v00001022d000015E1sv00001025sd00001456bc0Csc03i30"
  Driver Info #0:
    Driver Status: xhci_pci is active
    Driver Activation Cmd: "modprobe xhci_pci"
  Config Status: cfg=new, avail=yes, need=no, active=unknown
  Attached to: #20 (PCI bridge)

sudo inxi -Fazc0 --usb:

System:
  Kernel: 6.6.26-1-MANJARO arch: x86_64 bits: 64 compiler: gcc v: 13.2.1
    clocksource: tsc avail: hpet,acpi_pm
    parameters: BOOT_IMAGE=/boot/vmlinuz-6.6-x86_64
    root=UUID=fac3077d-c6ec-4ddd-8a21-214d4a3e9017 rw quiet apparmor=1
    security=apparmor udev.log_priority=3
  Desktop: Cinnamon v: 6.0.4 tk: GTK v: 3.24.41 wm: Muffin v: 6.0.1 tools:
    avail: cinnamon-screensaver dm: LightDM v: 1.32.0 Distro: Manjaro
    base: Arch Linux
Machine:
  Type: Laptop System: Acer product: Aspire A315-23 v: V1.21 serial: <filter>
  Mobo: DL model: Lotus_DA v: V1.21 serial: <filter>
    part-nu: 0000000000000000 uuid: b854e3ca-854a-2e4c-96dd-b4a9fca2c912
    UEFI: Insyde v: 1.21 date: 09/08/2022
Battery:
  ID-1: BAT1 charge: 15.5 Wh (59.2%) condition: 26.2/37.0 Wh (70.7%)
    volts: 7.4 min: 7.6 model: MURATA AP16M4J type: Li-ion serial: <filter>
    status: discharging
CPU:
  Info: model: AMD Ryzen 5 3500U with Radeon Vega Mobile Gfx socket: FP5
    bits: 64 type: MT MCP arch: Zen/Zen+ note: check gen: 1 level: v3
    note: check built: 2019 process: GF 12nm family: 0x17 (23)
    model-id: 0x18 (24) stepping: 1 microcode: 0x8108109
  Topology: cpus: 1x cores: 4 tpc: 2 threads: 8 smt: enabled cache:
    L1: 384 KiB desc: d-4x32 KiB; i-4x64 KiB L2: 2 MiB desc: 4x512 KiB L3: 4 MiB
    desc: 1x4 MiB
  Speed (MHz): avg: 1400 min/max: 1400/2100 boost: enabled
    base/boost: 2100/3700 scaling: driver: acpi-cpufreq governor: schedutil
    volts: 1.2 V ext-clock: 100 MHz cores: 1: 1400 2: 1400 3: 1400 4: 1400
    5: 1400 6: 1400 7: 1400 8: 1400 bogomips: 33609
  Flags: avx avx2 ht lm nx pae sse sse2 sse3 sse4_1 sse4_2 sse4a ssse3 svm
  Vulnerabilities:
  Type: gather_data_sampling status: Not affected
  Type: itlb_multihit status: Not affected
  Type: l1tf status: Not affected
  Type: mds status: Not affected
  Type: meltdown status: Not affected
  Type: mmio_stale_data status: Not affected
  Type: reg_file_data_sampling status: Not affected
  Type: retbleed mitigation: untrained return thunk; SMT vulnerable
  Type: spec_rstack_overflow mitigation: Safe RET
  Type: spec_store_bypass mitigation: Speculative Store Bypass disabled via
    prctl
  Type: spectre_v1 mitigation: usercopy/swapgs barriers and __user pointer
    sanitization
  Type: spectre_v2 mitigation: Retpolines; IBPB: conditional; STIBP:
    disabled; RSB filling; PBRSB-eIBRS: Not affected; BHI: Not affected
  Type: srbds status: Not affected
  Type: tsx_async_abort status: Not affected
Graphics:
  Device-1: AMD Picasso/Raven 2 [Radeon Vega Series / Radeon Mobile Series]
    vendor: Acer Incorporated ALI driver: amdgpu v: kernel arch: GCN-5
    code: Vega process: GF 14nm built: 2017-20 pcie: gen: 3 speed: 8 GT/s
    lanes: 16 ports: active: eDP-1 empty: HDMI-A-1 bus-ID: 05:00.0
    chip-ID: 1002:15d8 class-ID: 0300 temp: 44.0 C
  Display: server: X.org v: 1.21.1.12 with: Xwayland v: 23.2.6 driver: X:
    loaded: amdgpu unloaded: modesetting alternate: fbdev,vesa dri: radeonsi
    gpu: amdgpu display-ID: :0 screens: 1
  Screen-1: 0 s-res: 1920x1080 s-size: <missing: xdpyinfo>
  Monitor-1: eDP-1 mapped: eDP model: BOE Display 0x07cb built: 2018
    res: 1920x1080 hz: 60 dpi: 142 gamma: 1.2 size: 344x193mm (13.54x7.6")
    diag: 394mm (15.5") ratio: 16:9 modes: max: 1920x1080 min: 640x480
  API: EGL v: 1.5 hw: drv: amd radeonsi platforms: device: 0 drv: radeonsi
    device: 1 drv: swrast surfaceless: drv: radeonsi x11: drv: radeonsi
    inactive: gbm,wayland
  API: OpenGL v: 4.6 compat-v: 4.5 vendor: amd mesa v: 24.0.2-manjaro1.1
    glx-v: 1.4 direct-render: yes renderer: AMD Radeon Vega 8 Graphics
    (radeonsi raven LLVM 16.0.6 DRM 3.54 6.6.26-1-MANJARO)
    device-ID: 1002:15d8 memory: 1.95 GiB unified: no
Audio:
  Device-1: AMD Raven/Raven2/Fenghuang HDMI/DP Audio
    vendor: Acer Incorporated ALI driver: snd_hda_intel v: kernel pcie: gen: 3
    speed: 8 GT/s lanes: 16 bus-ID: 05:00.1 chip-ID: 1002:15de class-ID: 0403
  Device-2: AMD ACP/ACP3X/ACP6x Audio Coprocessor
    vendor: Acer Incorporated ALI driver: snd_pci_acp3x v: kernel
    alternate: snd_rn_pci_acp3x, snd_pci_acp5x, snd_pci_acp6x, snd_acp_pci,
    snd_rpl_pci_acp6x, snd_pci_ps, snd_sof_amd_renoir, snd_sof_amd_rembrandt,
    snd_sof_amd_vangogh pcie: gen: 3 speed: 8 GT/s lanes: 16 bus-ID: 05:00.5
    chip-ID: 1022:15e2 class-ID: 0480
  Device-3: AMD Family 17h/19h HD Audio vendor: Acer Incorporated ALI
    driver: snd_hda_intel v: kernel pcie: gen: 3 speed: 8 GT/s lanes: 16
    bus-ID: 05:00.6 chip-ID: 1022:15e3 class-ID: 0403
  API: ALSA v: k6.6.26-1-MANJARO status: kernel-api with: aoss
    type: oss-emulator tools: alsactl,alsamixer,amixer
  Server-1: JACK v: 1.9.22 status: off tools: N/A
  Server-2: PipeWire v: 1.0.3 status: n/a (root, process) tools: pw-cli
  Server-3: PulseAudio v: 17.0 status: active (root, process)
    with: pulseaudio-alsa type: plugin tools: pacat,pactl,pavucontrol
Network:
  Device-1: Qualcomm Atheros QCA9377 802.11ac Wireless Network Adapter
    vendor: Lite-On driver: ath10k_pci v: kernel pcie: gen: 1 speed: 2.5 GT/s
    lanes: 1 bus-ID: 02:00.0 chip-ID: 168c:0042 class-ID: 0280
  IF: wlp2s0 state: up mac: <filter>
  Device-2: Realtek RTL8111/8168/8211/8411 PCI Express Gigabit Ethernet
    vendor: Acer Incorporated ALI RTL8111/8168/8411 driver: r8169 v: kernel
    pcie: speed: Unknown lanes: 63 link-max: gen: 6 speed: 64 GT/s port: 2000
    bus-ID: 03:00.0 chip-ID: 10ec:8168 class-ID: 0200
  IF: enp3s0 state: down mac: <filter>
  Info: services: NetworkManager,wpa_supplicant
Drives:
  Local Storage: total: 953.87 GiB used: 108.58 GiB (11.4%)
  SMART Message: Required tool smartctl not installed. Check --recommends
  ID-1: /dev/nvme0n1 maj-min: 259:0 vendor: Western Digital model: PC SN530
    SDBPNPZ-1T00-1014 size: 953.87 GiB block-size: physical: 512 B
    logical: 512 B speed: 31.6 Gb/s lanes: 4 tech: SSD serial: <filter>
    fw-rev: 21103900 temp: 38.9 C scheme: GPT
Partition:
  ID-1: / raw-size: 373.08 GiB size: 366.15 GiB (98.14%)
    used: 108.51 GiB (29.6%) fs: ext4 block-size: 4096 B dev: /dev/nvme0n1p5
    maj-min: 259:5
  ID-2: /boot/efi raw-size: 100 MiB size: 96 MiB (96.00%)
    used: 70.8 MiB (73.8%) fs: vfat block-size: 512 B dev: /dev/nvme0n1p1
    maj-min: 259:1
Swap:
  Alert: No swap data was found.
USB:
  Hub-1: 1-0:1 info: hi-speed hub with single TT ports: 4 rev: 2.0
    speed: 480 Mb/s (57.2 MiB/s) lanes: 1 mode: 2.0 chip-ID: 1d6b:0002
    class-ID: 0900
  Hub-2: 2-0:1 info: super-speed hub ports: 4 rev: 3.1
    speed: 10 Gb/s (1.16 GiB/s) lanes: 1 mode: 3.2 gen-2x1 chip-ID: 1d6b:0003
    class-ID: 0900
  Hub-3: 3-0:1 info: hi-speed hub with single TT ports: 2 rev: 2.0
    speed: 480 Mb/s (57.2 MiB/s) lanes: 1 mode: 2.0 chip-ID: 1d6b:0002
    class-ID: 0900
  Hub-4: 4-0:1 info: super-speed hub ports: 1 rev: 3.1
    speed: 10 Gb/s (1.16 GiB/s) lanes: 1 mode: 3.2 gen-2x1 chip-ID: 1d6b:0003
    class-ID: 0900
Sensors:
  System Temperatures: cpu: 44.6 C mobo: N/A gpu: amdgpu temp: 44.0 C
  Fan Speeds (rpm): N/A
Info:
  Memory: total: 20 GiB note: est. available: 17.5 GiB used: 3.49 GiB (20.0%)
  Processes: 282 Power: uptime: 48m states: freeze,mem,disk suspend: deep
    avail: s2idle wakeups: 0 hibernate: platform avail: shutdown, reboot,
    suspend, test_resume image: 6.99 GiB services: csd-power,upowerd
    Init: systemd v: 255 default: graphical tool: systemctl
  Packages: 1432 pm: pacman pkgs: 1417 libs: 368 tools: pamac,yay
    pm: flatpak pkgs: 15 Compilers: clang: 16.0.6 gcc: 13.2.1 Shell: Sudo (sudo)
    v: 1.9.15p5 default: Bash v: 5.2.26 running-in: gnome-terminal
    inxi: 3.3.34

I hope I can get at least usb 2.0 working again. USB 3.0 hadn’t mattered for 4 months so it should be fine.
Thank you to everyone who takes their time to help me.

3

The linked thread does not have a marked solution.

Your example commands only really show you 'modprobe’ing some modules.

modprobe does not persist across reboots, so that cant be the problem.

Did you make package changes or some configuration edits aside from the listed commands?

The history command or /var/log/pacman.log file may be helpful for you to look at.

4

Ok, strange, after reboot the usb 2.0 was still not working after loading into the user

this is the recent pacman log

...
[2024-04-23T08:07:55+0200] [ALPM] transaction completed
[2024-04-23T08:07:55+0200] [ALPM] running '30-systemd-update.hook'...
[2024-04-23T08:07:55+0200] [ALPM] running 'gtk-update-icon-cache.hook'...
[2024-04-23T08:07:55+0200] [ALPM] running 'thunderbird-post.hook'...
[2024-04-23T08:07:55+0200] [ALPM] running 'update-desktop-database.hook'...
[2024-04-25T08:07:25+0200] [PAMAC] synchronizing package lists
[2024-04-25T08:07:59+0200] [ALPM] transaction started
[2024-04-25T08:07:59+0200] [ALPM] upgraded kvantum-manjaro (0.13.5+5+g0179d45-1 -> 0.13.5+5+g0179d45-3)
[2024-04-25T08:08:00+0200] [ALPM] transaction completed
[2024-04-25T08:08:00+0200] [ALPM] running '30-systemd-update.hook'...
[2024-04-25T16:34:08+0200] [PACMAN] Running 'pacman -S python-pypdf'
[2024-04-25T16:35:10+0200] [ALPM] transaction started
[2024-04-25T16:35:10+0200] [ALPM] installed python-flit-core (3.9.0-2)
[2024-04-25T16:35:10+0200] [ALPM] transaction completed
[2024-04-25T16:35:10+0200] [ALPM] running '30-systemd-update.hook'...
[2024-04-25T16:35:26+0200] [ALPM] transaction started
[2024-04-25T16:35:26+0200] [ALPM] installed python-pypdf2 (1:2.12.1-3)
[2024-04-25T16:35:27+0200] [ALPM] transaction completed
[2024-04-25T16:35:27+0200] [ALPM] running '30-systemd-update.hook'...
[2024-04-25T16:36:38+0200] [ALPM] transaction started
[2024-04-25T16:36:38+0200] [ALPM] removed python-pypdf2 (1:2.12.1-3)
[2024-04-25T16:36:39+0200] [ALPM] transaction completed
[2024-04-25T16:36:39+0200] [ALPM] running '30-systemd-update.hook'...
[2024-04-25T16:36:47+0200] [ALPM] transaction started
[2024-04-25T16:36:47+0200] [ALPM] installed python-pypdf3 (1.0.6-4)
[2024-04-25T16:36:47+0200] [ALPM] transaction completed
[2024-04-25T16:36:47+0200] [ALPM] running '30-systemd-update.hook'...
[2024-05-05T11:20:14+0200] [PAMAC] synchronizing package lists
[2024-05-05T11:21:16+0200] [ALPM] transaction started
[2024-05-05T11:21:19+0200] [ALPM] upgraded vivaldi (6.6.3271.61-1 -> 6.7.3329.24-1)
[2024-05-05T11:21:19+0200] [ALPM] upgraded vivaldi-ffmpeg-codecs (122.0.6261.84-1 -> 124.0.6367.82-1)
[2024-05-05T11:21:19+0200] [ALPM] transaction completed
[2024-05-05T11:21:19+0200] [ALPM] running '30-systemd-update.hook'...
[2024-05-05T11:21:19+0200] [ALPM] running 'gtk-update-icon-cache.hook'...
[2024-05-05T11:21:19+0200] [ALPM] running 'update-desktop-database.hook'...
[2024-05-09T14:31:21+0200] [PAMAC] synchronizing package lists
[2024-05-09T14:33:09+0200] [ALPM] transaction started
[2024-05-09T14:33:10+0200] [ALPM] upgraded vivaldi (6.7.3329.24-1 -> 6.7.3329.26-1)
[2024-05-09T14:33:10+0200] [ALPM] transaction completed
[2024-05-09T14:33:10+0200] [ALPM] running '30-systemd-update.hook'...
[2024-05-09T14:33:10+0200] [ALPM] running 'gtk-update-icon-cache.hook'...
[2024-05-09T14:33:10+0200] [ALPM] running 'update-desktop-database.hook'...
[2024-05-09T14:36:03+0200] [ALPM] transaction started
[2024-05-09T14:36:03+0200] [ALPM] reinstalled pulseaudio-bluetooth (17.0-3)
[2024-05-09T14:36:03+0200] [ALPM] transaction completed
[2024-05-09T14:36:03+0200] [ALPM] running '30-systemd-update.hook'...
[2024-05-09T14:36:32+0200] [ALPM] transaction started
[2024-05-09T14:36:32+0200] [ALPM] reinstalled bluez (5.72-2)
[2024-05-09T14:36:32+0200] [ALPM] reinstalled bluez-libs (5.72-2)
[2024-05-09T14:36:32+0200] [ALPM] transaction completed
[2024-05-09T14:36:32+0200] [ALPM] running '30-systemd-daemon-reload-system.hook'...
[2024-05-09T14:36:32+0200] [ALPM] running '30-systemd-update.hook'...
[2024-05-09T14:36:32+0200] [ALPM] running 'dbus-reload.hook'...
[2024-05-09T15:33:34+0200] [PACMAN] Running '/usr/bin/pacman --noconfirm --noprogressbar -S linux66'
[2024-05-09T15:34:36+0200] [ALPM] transaction started
[2024-05-09T15:34:37+0200] [ALPM] installed linux66 (6.6.26-1)
[2024-05-09T15:34:38+0200] [ALPM] transaction completed
[2024-05-09T15:34:38+0200] [ALPM] running '30-systemd-update.hook'...
[2024-05-09T15:34:38+0200] [ALPM] running '60-depmod.hook'...
[2024-05-09T15:34:39+0200] [ALPM] running '90-mkinitcpio-install.hook'...
[2024-05-09T15:34:39+0200] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux66.preset: 'default'
[2024-05-09T15:34:39+0200] [ALPM-SCRIPTLET] ==> Using default configuration file: '/etc/mkinitcpio.conf'
[2024-05-09T15:34:39+0200] [ALPM-SCRIPTLET]   -> -k /boot/vmlinuz-6.6-x86_64 -g /boot/initramfs-6.6-x86_64.img --microcode /boot/amd-ucode.img
[2024-05-09T15:34:39+0200] [ALPM-SCRIPTLET] ==> Starting build: '6.6.26-1-MANJARO'
[2024-05-09T15:34:39+0200] [ALPM-SCRIPTLET]   -> Running build hook: [base]
[2024-05-09T15:34:40+0200] [ALPM-SCRIPTLET]   -> Running build hook: [udev]
[2024-05-09T15:34:40+0200] [ALPM-SCRIPTLET]   -> Running build hook: [autodetect]
[2024-05-09T15:34:40+0200] [ALPM-SCRIPTLET]   -> Running build hook: [modconf]
[2024-05-09T15:34:40+0200] [ALPM-SCRIPTLET]   -> Running build hook: [block]
[2024-05-09T15:34:41+0200] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: 'xhci_pci'
[2024-05-09T15:34:41+0200] [ALPM-SCRIPTLET]   -> Running build hook: [keyboard]
[2024-05-09T15:34:41+0200] [ALPM-SCRIPTLET]   -> Running build hook: [keymap]
[2024-05-09T15:34:41+0200] [ALPM-SCRIPTLET]   -> Running build hook: [consolefont]
[2024-05-09T15:34:41+0200] [ALPM-SCRIPTLET] ==> WARNING: consolefont: no font found in configuration
[2024-05-09T15:34:41+0200] [ALPM-SCRIPTLET]   -> Running build hook: [filesystems]
[2024-05-09T15:34:41+0200] [ALPM-SCRIPTLET]   -> Running build hook: [fsck]
[2024-05-09T15:34:41+0200] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2024-05-09T15:34:42+0200] [ALPM-SCRIPTLET] ==> Creating gzip-compressed initcpio image: '/boot/initramfs-6.6-x86_64.img'
[2024-05-09T15:34:43+0200] [ALPM-SCRIPTLET] ==> Image generation successful
[2024-05-09T15:34:43+0200] [ALPM-SCRIPTLET] ==> Building image from preset: /etc/mkinitcpio.d/linux66.preset: 'fallback'
[2024-05-09T15:34:43+0200] [ALPM-SCRIPTLET] ==> Using default configuration file: '/etc/mkinitcpio.conf'
[2024-05-09T15:34:43+0200] [ALPM-SCRIPTLET]   -> -k /boot/vmlinuz-6.6-x86_64 -g /boot/initramfs-6.6-x86_64-fallback.img -S autodetect --microcode /boot/amd-ucode.img
[2024-05-09T15:34:43+0200] [ALPM-SCRIPTLET] ==> Starting build: '6.6.26-1-MANJARO'
[2024-05-09T15:34:43+0200] [ALPM-SCRIPTLET]   -> Running build hook: [base]
[2024-05-09T15:34:44+0200] [ALPM-SCRIPTLET]   -> Running build hook: [udev]
[2024-05-09T15:34:44+0200] [ALPM-SCRIPTLET]   -> Running build hook: [modconf]
[2024-05-09T15:34:44+0200] [ALPM-SCRIPTLET]   -> Running build hook: [block]
[2024-05-09T15:34:44+0200] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: 'qla1280'
[2024-05-09T15:34:45+0200] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: 'bfa'
[2024-05-09T15:34:45+0200] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: 'qed'
[2024-05-09T15:34:45+0200] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: 'aic94xx'
[2024-05-09T15:34:45+0200] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: 'wd719x'
[2024-05-09T15:34:46+0200] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: 'qla2xxx'
[2024-05-09T15:34:46+0200] [ALPM-SCRIPTLET] ==> WARNING: Possibly missing firmware for module: 'xhci_pci'
[2024-05-09T15:34:49+0200] [ALPM-SCRIPTLET]   -> Running build hook: [keyboard]
[2024-05-09T15:34:50+0200] [ALPM-SCRIPTLET]   -> Running build hook: [keymap]
[2024-05-09T15:34:50+0200] [ALPM-SCRIPTLET]   -> Running build hook: [consolefont]
[2024-05-09T15:34:50+0200] [ALPM-SCRIPTLET] ==> WARNING: consolefont: no font found in configuration
[2024-05-09T15:34:50+0200] [ALPM-SCRIPTLET]   -> Running build hook: [filesystems]
[2024-05-09T15:34:52+0200] [ALPM-SCRIPTLET]   -> Running build hook: [fsck]
[2024-05-09T15:34:55+0200] [ALPM-SCRIPTLET] ==> Generating module dependencies
[2024-05-09T15:34:55+0200] [ALPM-SCRIPTLET] ==> Creating gzip-compressed initcpio image: '/boot/initramfs-6.6-x86_64-fallback.img'
[2024-05-09T15:35:02+0200] [ALPM-SCRIPTLET] ==> Image generation successful
[2024-05-09T15:35:02+0200] [ALPM] running '99-update-grub.hook'...
[2024-05-09T15:35:03+0200] [ALPM-SCRIPTLET] Generating grub configuration file ...
[2024-05-09T15:35:03+0200] [ALPM-SCRIPTLET] Found linux image: /boot/vmlinuz-6.6-x86_64
[2024-05-09T15:35:03+0200] [ALPM-SCRIPTLET] Found initrd image: /boot/amd-ucode.img /boot/initramfs-6.6-x86_64.img
[2024-05-09T15:35:03+0200] [ALPM-SCRIPTLET] Found initrd fallback image: /boot/initramfs-6.6-x86_64-fallback.img
[2024-05-09T15:35:03+0200] [ALPM-SCRIPTLET] Found linux image: /boot/vmlinuz-6.5-x86_64
[2024-05-09T15:35:04+0200] [ALPM-SCRIPTLET] Found initrd image: /boot/amd-ucode.img /boot/initramfs-6.5-x86_64.img
[2024-05-09T15:35:04+0200] [ALPM-SCRIPTLET] Found initrd fallback image: /boot/initramfs-6.5-x86_64-fallback.img
[2024-05-09T15:35:04+0200] [ALPM-SCRIPTLET] Warning: os-prober will be executed to detect other bootable partitions.
[2024-05-09T15:35:04+0200] [ALPM-SCRIPTLET] Its output will be used to detect bootable binaries on them and create new boot entries.
[2024-05-09T15:35:06+0200] [ALPM-SCRIPTLET] Found Windows Boot Manager on /dev/nvme0n1p1@/EFI/Microsoft/Boot/bootmgfw.efi
[2024-05-09T15:35:06+0200] [ALPM-SCRIPTLET] Adding boot menu entry for UEFI Firmware Settings ...
[2024-05-09T15:35:06+0200] [ALPM-SCRIPTLET] Found memtest86+ image: /boot/memtest86+/memtest.bin
[2024-05-09T15:35:06+0200] [ALPM-SCRIPTLET] /usr/bin/grub-probe: warning: unknown device type nvme0n1.
[2024-05-09T15:35:06+0200] [ALPM-SCRIPTLET] done
[2024-05-09T22:33:17+0200] [ALPM] transaction started
[2024-05-09T22:33:17+0200] [ALPM] installed i2c-tools (4.3-4)
[2024-05-09T22:33:17+0200] [ALPM] installed ddcutil (2.1.4-1)
[2024-05-09T22:33:17+0200] [ALPM] installed net-tools (2.10-2)
[2024-05-09T22:33:17+0200] [ALPM] installed acpica (20230628-1)
[2024-05-09T22:33:17+0200] [ALPM] transaction completed
[2024-05-09T22:33:17+0200] [ALPM] running '20-systemd-sysusers.hook'...
[2024-05-09T22:33:17+0200] [ALPM-SCRIPTLET] Creating group 'i2c' with GID 958.
[2024-05-09T22:33:17+0200] [ALPM] running '30-systemd-udev-reload.hook'...
[2024-05-09T22:33:18+0200] [ALPM] running '30-systemd-update.hook'...
[2024-05-09T22:33:52+0200] [ALPM] transaction started
[2024-05-09T22:33:52+0200] [ALPM] installed edid-decode-git (r676.3d63549-1)
[2024-05-09T22:33:52+0200] [ALPM] transaction completed
[2024-05-09T22:33:52+0200] [ALPM] running '30-systemd-update.hook'...
[2024-05-09T22:34:00+0200] [ALPM] transaction started
[2024-05-09T22:34:00+0200] [ALPM] installed hw-probe (1.6.5-2)
[2024-05-09T22:34:01+0200] [ALPM] transaction completed
[2024-05-09T22:34:01+0200] [ALPM] running '30-systemd-update.hook'...
5

I notice you have an EOL kernel, which can only be causing problems.

It appears you have booted into 6.6 at the time of your inxi, so you can remove linux65 (and any associated packages).

On a related note - you may have changed kernels around the time of your issue. You may wish to also try the previous LTS kernel linux61.

1 Like
6

I just removed the old kernal with the manjaro settings manager. Does it also clear the packages?
I rebooted after and usb 2.0 is still broken.
As said the usb 3.0 issue was there for months since install, but 2.0 is new.
Both would be nice to fix.
While trying to fix 3.0 I had the a mouse connected to 2.0 which stopped working after the first modprobe and doesn’t work on the desktop since. It work in the lockscreen before entering the user though. So I am even more confused with it.

By the way thank you for taking your time

EDIT:
I just pugged my laptop in and for some reason in that case the usb-mouse works after getting onto the desktop, but when I unplugged the charger the mouse stopped working and after pluging it in again the mouse still didn’t work, even after repluging it.
So usb 2.0 works if the device is plugged in during login/boot and if the laptop is chargin? It is very confusing.

7

mhwd-kernel instructs the packages to be removed.
I dont know what further clearing you may be referring to … the package cache would not be cleared until some later invocation of something like paccache -rvuk0 or similar.

So it maybe have been an observed difference that did not take into account the plug?

Sounds like autosleep of the usb to me. Maybe from something like tlp.

Do you have some power management running like that? ex:

systemctl status tlp

8

You might also check your BIOS settings; see if legacy USB settings are enabled. Enabling those settings (if they exist) might (or might not) make any difference, but it’s worth trying. Cheers.

9

Sounds like you unloaded needed modules for USB to work.

A default Manjaro Linux system does not disable hardware - but dual boot with Windows may create unknown issues - especially if one does not shutdown Windows cleanly - that means disable Windows Fast Boot and Windows hibernate - always clean shutdown of Windows.

1 Like
10

So, I deactivated Windows 10 fast boot and even though I do not have the hybernate option, made shure it is deactiveted.
Nothing changed.
In UEFI I looked for an USB option, but there were very few options in gereral and there was no option for legacy USB.

systemctl status tlp

● tlp.service - TLP system startup/shutdown
     Loaded: loaded (/usr/lib/systemd/system/tlp.service; enabled; preset: disabled)
     Active: active (exited) since Fri 2024-05-10 13:22:32 CEST; 2min 55s ago
       Docs: https://linrunner.de/tlp
    Process: 934 ExecStart=/usr/bin/tlp init start (code=exited, status=0/SUCCESS)
   Main PID: 934 (code=exited, status=0/SUCCESS)
        CPU: 422ms

Mai 10 13:22:31 niclas-aspirea systemd[1]: Starting TLP system startup/shutdown...
Mai 10 13:22:32 niclas-aspirea tlp[934]: Applying power save settings...done.
Mai 10 13:22:32 niclas-aspirea tlp[934]: Setting battery charge thresholds...done.
Mai 10 13:22:32 niclas-aspirea systemd[1]: Finished TLP system startup/shutdown.

EDIT:
I was unshure if the manjaro settings manager will remove the packages when removing the kernel. Because i didn’t run any commands and did it with the ui.

11

And if you

systemctl disable tlp --now

??

12

So I ran the command, nothing happened, I rebooted with the laptop charging, the usb-mouse worked even after login, but stopped working when the laptop stopped charging and then refuses to work even when charging. But in the short time all 3 usb ports worked (regardless of 2.0 or 3.0) with the mouse.
So, I think we are getting closer.

13

That indicates one of two causes

  • flaky electronics (you already ruled that out)
  • power is cut to USB devices by a power profile of some kind

No - you are getting closer … we are merely providing ideas - you are the one to do the work.

You will need to go over your power settings and you may have conflicting settings provided by different daemons.

First look towards a GUI settings panel somewhere allowing you to adjust settings.

Then - I don’t know …

Judging from a search - that specific Acer model appears to have issues with USB on Linux.

14

Thank you for you help.

So averall I narrowed it down to TLP.
When TLP is enabled, it suspends the usb ports when not charging and doesn’t let them come back on.

But when TLP is disabled with TLP-UI, when I unplug the charger the ports keep working without any issues.

only disabling usb-suspend in the tlp ui does nothing against the issue, so maybe it is some other setting that overlaps or just interferes with the usb ports in general.

In any case I will keep looking into it.

15

Ok, maybe this is not completly ok , but in hwinfo --usb-ctrl is said “Attached to: #20 (PCI bridge)”.
I disabled Runtime Powermanagement for PCIe bus devices in the UI, and it seems to work. The Usb are not shut down in Battery mode.

I changed in TLP UI
PCIe → RUNTIME PM → RUNTIME_PN_ON_BAT → off

and now it seems to work. I will mark it as the solution after a few tests.

EDIT: I have now tested it with the usb mouse and an external hardrive, even after a reboot the problem seems to be solved.

EDIT2: I looked through the messages again @cscs had the right Idea, but when disabling even with tlp ui, it seems that it does not re-enable the suspended usb ports, but only stop it. So I couldn’t see it working since when the command was run the devices where already turned off. But when they were on, it would likely have solved the problem.

2 Likes
16

This topic was automatically closed 36 hours after the last reply. New replies are no longer allowed.