Hello guys.I’ve trying to connect bluetooth but it didn’t even open.I’ve tried to open with the comment
sudo systemctl start bluetooth
but it don’t work and i’ve even tried to create main and audio config files but it said the partition is only readable.What else can i do to connect a bluetooth headphone.
Welcome to Manjaro!
Please read this:
and post some more information so we can see what’s really going on. Now we know the symptom of the disease, but we need some more probing to know where the origin lies…
inxi --admin --verbosity=7 --filter --no-host --width would be the minimum required information… (Personally Identifiable Information like serial numbers and MAC addresses will be filtered out by the above command)rfkill list would be helpful as well.
P.S. If you enter a bit more details in your profile, we can also see which Desktop Environment you’re using, which CPU/GPU you have, …
The out put of rfkill list is:
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
and the output of inxi --admin --verbosity=7 --filter --no-host --width is:
System:
Kernel: 5.8.6-1-MANJARO x86_64 bits: 64 compiler: N/A
parameters: BOOT_IMAGE=/boot/vmlinuz-5.8-x86_64
root=UUID=64d70f14-4560-46a2-b2f9-406d081490b3 rw quiet apparmor=1
security=apparmor resume=UUID=b27c0610-2de0-4a8e-a8e6-77cbaf17cc4b
udev.log_priority=3
Desktop: Xfce 4.14.2 tk: Gtk 3.24.20 info: xfce4-panel wm: xfwm4
dm: LightDM 1.30.0 Distro: Manjaro Linux
Machine:
Type: Laptop System: Hewlett-Packard product: HP ProBook 430 G1
v: A3009DD10303 serial: <filter> Chassis: type: 10 serial: <filter>
Mobo: Hewlett-Packard model: 1946 v: KBC Version 89.17 serial: <filter>
BIOS: Hewlett-Packard v: L73 Ver. 01.49 date: 08/29/2019
Battery:
ID-1: BAT0 charge: 94.5 Wh condition: 111.3/111.3 Wh (100%) volts: 15.3/14.8
model: Hewlett-Packard Primary type: Li-ion serial: <filter>
status: Discharging
Memory:
RAM: total: 3.73 GiB used: 2.61 GiB (70.0%)
RAM Report: permissions: Unable to run dmidecode. Root privileges required.
CPU:
Topology: Dual Core model: Intel Core i5-4200U bits: 64 type: MT MCP
arch: Haswell family: 6 model-id: 45 (69) stepping: 1 microcode: 26
L2 cache: 3072 KiB bogomips: 18366
Speed: 1611 MHz min/max: 800/2600 MHz Core speeds (MHz): 1: 2264 2: 2290
3: 2289 4: 2282
Flags: abm acpi aes aperfmperf apic arat arch_perfmon avx avx2 bmi1 bmi2 bts
clflush cmov constant_tsc cpuid cpuid_fault cx16 cx8 de ds_cpl dtes64 dtherm
dts epb ept ept_ad erms est f16c flexpriority flush_l1d fma fpu fsgsbase
fxsr ht ibpb ibrs ida invpcid invpcid_single lahf_lm lm mca mce md_clear mmx
monitor movbe msr mtrr nonstop_tsc nopl nx pae pat pbe pcid pclmulqdq pdcm
pdpe1gb pebs pge pln pni popcnt pse pse36 pti pts rdrand rdtscp rep_good
sdbg sep smep ss ssbd sse sse2 sse4_1 sse4_2 ssse3 stibp syscall tm tm2
tpr_shadow tsc tsc_adjust tsc_deadline_timer vme vmx vnmi vpid xsave
xsaveopt xtopology xtpr
Vulnerabilities: Type: itlb_multihit status: KVM: VMX disabled
Type: l1tf
mitigation: PTE Inversion; VMX: conditional cache flushes, SMT vulnerable
Type: mds mitigation: Clear CPU buffers; SMT vulnerable
Type: meltdown mitigation: PTI
Type: spec_store_bypass
mitigation: Speculative Store Bypass disabled via prctl and seccomp
Type: spectre_v1
mitigation: usercopy/swapgs barriers and __user pointer sanitization
Type: spectre_v2 mitigation: Full generic retpoline, IBPB: conditional,
IBRS_FW, STIBP: conditional, RSB filling
Type: srbds mitigation: Microcode
Type: tsx_async_abort status: Not affected
Graphics:
Device-1: Intel Haswell-ULT Integrated Graphics vendor: Hewlett-Packard
driver: i915 v: kernel bus ID: 00:02.0 chip ID: 8086:0a16
Device-2: Chicony HP HD Webcam type: USB driver: uvcvideo bus ID: 2-7:6
chip ID: 04f2:b3c8 serial: <filter>
Display: x11 server: X.Org 1.20.8 driver: intel unloaded: modesetting
alternate: fbdev,vesa display ID: :0.0 screens: 1
Screen-1: 0 s-res: 1366x768 s-dpi: 96 s-size: 361x203mm (14.2x8.0")
s-diag: 414mm (16.3")
Monitor-1: eDP1 res: 1366x768 hz: 60 dpi: 120 size: 290x160mm (11.4x6.3")
diag: 331mm (13")
OpenGL: renderer: Mesa DRI Intel HD Graphics 4400 (HSW GT2)
v: 4.5 Mesa 20.1.7 compat-v: 3.0 direct render: Yes
Audio:
Device-1: Intel Haswell-ULT HD Audio vendor: Hewlett-Packard
driver: snd_hda_intel v: kernel bus ID: 00:03.0 chip ID: 8086:0a0c
Device-2: Intel 8 Series HD Audio vendor: Hewlett-Packard
driver: snd_hda_intel v: kernel bus ID: 00:1b.0 chip ID: 8086:9c20
Sound Server: ALSA v: k5.8.6-1-MANJARO
Network:
Device-1: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet
vendor: Hewlett-Packard driver: r8168 v: 8.048.03-NAPI modules: r8169
port: 3000 bus ID: 03:00.0 chip ID: 10ec:8168
IF: enp3s0 state: down mac: <filter>
Device-2: MEDIATEK MT7630e 802.11bgn Wireless Network Adapter
vendor: Hewlett-Packard driver: mt76x0e v: kernel port: 3000 bus ID: 04:00.0
chip ID: 14c3:7630
IF: wlo1 state: up mac: <filter>
IP v4: <filter> type: dynamic noprefixroute scope: global
broadcast: <filter>
IP v6: <filter> type: noprefixroute scope: link
WAN IP: <filter>
Drives:
Local Storage: total: 465.76 GiB used: 113.87 GiB (24.4%)
SMART Message: Required tool smartctl not installed. Check --recommends
ID-1: /dev/sda vendor: Seagate model: ST500LM021-1KJ152 size: 465.76 GiB
block size: physical: 4096 B logical: 512 B speed: 6.0 Gb/s
rotation: 7200 rpm serial: <filter> rev: LIM1 scheme: MBR
Message: No Optical or Floppy data was found.
RAID:
Message: No RAID data was found.
Partition:
ID-1: / raw size: 457.56 GiB size: 449.38 GiB (98.21%)
used: 112.68 GiB (25.1%) fs: ext4 dev: /dev/sda1 label: N/A
uuid: 64d70f14-4560-46a2-b2f9-406d081490b3
Swap:
Kernel: swappiness: 60 (default) cache pressure: 100 (default)
ID-1: swap-1 type: partition size: 8.20 GiB used: 1.19 GiB (14.5%)
priority: -2 dev: /dev/sda2 label: N/A
uuid: b27c0610-2de0-4a8e-a8e6-77cbaf17cc4b
Unmounted:
Message: No unmounted partitions found.
USB:
Hub: 1-0:1 info: Full speed (or root) Hub ports: 2 rev: 2.0 speed: 480 Mb/s
chip ID: 1d6b:0002
Hub: 1-1:2 info: Intel Integrated Rate Matching Hub ports: 8 rev: 2.0
speed: 480 Mb/s chip ID: 8087:8000
Hub: 2-0:1 info: Full speed (or root) Hub ports: 9 rev: 2.0 speed: 480 Mb/s
chip ID: 1d6b:0002
Device-1: 2-2:2 info: Silicon Labs USB OPTICAL MOUSE type: Mouse
driver: hid-generic,usbhid interfaces: 1 rev: 2.0 speed: 1.5 Mb/s
chip ID: 10c4:8108
Device-2: 2-4:3 info: MediaTek MT7630e Bluetooth Adapter
type: <vendor specific> driver: N/A interfaces: 2 rev: 2.0 speed: 480 Mb/s
chip ID: 0e8d:763e serial: <filter>
Device-3: 2-5:4 info: Validity Sensors VFS495 Fingerprint Reader
type: <vendor specific> driver: N/A interfaces: 1 rev: 1.1 speed: 12 Mb/s
chip ID: 138a:003f serial: <filter>
Device-4: 2-6:5 info: Holtek Keyboard LKS02 type: Keyboard,HID
driver: hid-generic,usbhid interfaces: 2 rev: 1.1 speed: 1.5 Mb/s
chip ID: 04d9:1702
Device-5: 2-7:6 info: Chicony HP HD Webcam type: Video driver: uvcvideo
interfaces: 2 rev: 2.0 speed: 480 Mb/s chip ID: 04f2:b3c8 serial: <filter>
Hub: 3-0:1 info: Full speed (or root) Hub ports: 4 rev: 3.0 speed: 5 Gb/s
chip ID: 1d6b:0003
Sensors:
System Temperatures: cpu: 64.0 C mobo: N/A
Fan Speeds (RPM): N/A
Info:
Processes: 210 Uptime: 3h 57m Init: systemd v: 246 Compilers: gcc: 10.2.0
Packages: 1218 pacman: 1216 lib: 342 flatpak: 0 snap: 2 Shell: Bash
v: 5.0.18 running in: xfce4-terminal inxi: 3.1.05
is this useable cause I’m not a advanced user so
In the future, when providing code/output, please copy-paste that output in-between 3 backticks ``` at the beginning and end of the code/text so that the output looks like this:
Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua.
Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat.
Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur.
Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
instead of like this:
Lorem ipsum dolor sit amet, consectetur adipiscing elit, sed do eiusmod tempor incididunt ut labore et dolore magna aliqua. Ut enim ad minim veniam, quis nostrud exercitation ullamco laboris nisi ut aliquip ex ea commodo consequat. Duis aute irure dolor in reprehenderit in voluptate velit esse cillum dolore eu fugiat nulla pariatur. Excepteur sint occaecat cupidatat non proident, sunt in culpa qui officia deserunt mollit anim id est laborum.
(as that makes our life much easier so you get helped more quickly and efficiently)
No need to do anything right now as I’m an editor here on this site and have fixed it for you already. However, in the future I might not see your post so review my edits by pushing the orange pencil above the post I just fixed. 
According to this:
You don’t have a driver installed for your MT7630e and according to their website they don’t support Linux (any more: found some old drivers for the kernel 3 series, but nothing for the 5 series) and neither does HP.
People have tried using other drivers / Recompiling from source but I haven’t been able to find any working configurations, so the only answer I can give you is:
Buy a Bluetooth USB dongle that is Linux compatible…
ok thanks
This topic was automatically closed 15 days after the last reply. New replies are no longer allowed.