so install gparted in live usb, with it create a new partition table GPT, then format it in ext4 and try again
im getting an input/output error
doing what? formatting it ? your hard disk is probably corrupted
while trying to create a new partition table, i dont know how it can be corrupted though, its only a few months old
check the disks smart status via kde partition manager
also run check on it via kde partiton manager and just to be sure do it also with gparted
it says smart status is good but it has 1509 bad sectors
so your drive is damaged …
run check on it from kde partition manager
i cant find where to run a check on kde partition manager, i ran one on gparted though but even that failed to work. i think im just going to order a new hard drive. im really not getting anywhere with this, thanks for the help though.
and can you format the drive to ext4? or it fails too?
i cant really do anything, i cant format or delete partitions
so run the fsck as was recommended above:
sudo e2fsck -b 8193 /dev/sda
i have but it doesnt do anything, it just tells me “theres a bad magic number in the superblock” and “The superblock could not be read or does not describe a valid ext2/ext3/ext4 filesystem.”
output from this:
sudo smartctl -x /dev/sda
=== START OF INFORMATION SECTION ===
Device Model: WDC WD20EZBX-00AYRA0
Serial Number: WD-WXG2A71DZTSE
LU WWN Device Id: 5 0014ee 21495df83
Firmware Version: 01.01A01
User Capacity: 2,000,398,934,016 bytes [2.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 7200 rpm
Form Factor: 3.5 inches
TRIM Command: Available, deterministic
Device is: Not in smartctl database 7.3/5319
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Tue Aug 30 22:11:38 2022 BST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM feature is: Unavailable
Rd look-ahead is: Enabled
Write cache is: Enabled
DSN feature is: Unavailable
ATA Security is: Disabled, NOT FROZEN [SEC1]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 4200) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 23) minutes.
Conveyance self-test routine
recommended polling time: ( 2) minutes.
SCT capabilities: (0x3035) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 187 187 051 - 561
3 Spin_Up_Time POS--K 170 149 021 - 2483
4 Start_Stop_Count -O--CK 100 100 000 - 111
5 Reallocated_Sector_Ct PO--CK 162 162 140 - 1509
7 Seek_Error_Rate -OSR-K 137 110 000 - 8936
9 Power_On_Hours -O--CK 100 100 000 - 166
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 110
192 Power-Off_Retract_Count -O--CK 200 200 000 - 102
193 Load_Cycle_Count -O--CK 200 200 000 - 13
194 Temperature_Celsius -O---K 109 106 000 - 34
196 Reallocated_Event_Count -O--CK 001 001 000 - 1509
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 100 253 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x04 GPL R/O 256 Device Statistics log
0x04 SL R/O 8 Device Statistics log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x09 SL R/W 1 Selective self-test log
0x0c GPL R/O 2048 Pending Defects log
0x10 GPL R/O 1 NCQ Command Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x24 GPL R/O 294 Current Device Internal Status Data log
0x30 GPL,SL R/O 9 IDENTIFY DEVICE data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb6 GPL,SL VS 1 Device vendor specific log
0xb7 GPL,SL VS 74 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 93 Device vendor specific log
0xd7 GPL VS 1 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 46118 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 46118 [5] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 01 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:15.152 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:15.152 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:15.104 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 08 00:00:15.104 SET FEATURES [Set transfer mode]
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:15.104 READ LOG EXT
Error 46117 [4] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:15.152 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:15.104 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 08 00:00:15.104 SET FEATURES [Set transfer mode]
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:15.104 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:15.103 SET FEATURES [Enable SATA feature]
Error 46116 [3] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 45 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 45 00 00 00 00 00 00 a0 08 00:00:15.104 SET FEATURES [Set transfer mode]
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:15.104 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:15.103 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:15.103 IDENTIFY DEVICE
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:10.443 READ LOG EXT
Error 46115 [2] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 01 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:15.104 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:15.103 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:15.103 IDENTIFY DEVICE
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:10.443 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:10.443 SET FEATURES [Enable SATA feature]
Error 46114 [1] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:15.103 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:15.103 IDENTIFY DEVICE
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:10.443 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:10.443 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:09.563 IDENTIFY DEVICE
Error 46113 [0] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 01 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:10.443 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:10.443 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:09.563 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 08 00:00:09.563 SET FEATURES [Set transfer mode]
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:09.563 READ LOG EXT
Error 46112 [23] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 02 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:10.443 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:09.563 IDENTIFY DEVICE
ef 00 03 00 45 00 00 00 00 00 00 a0 08 00:00:09.563 SET FEATURES [Set transfer mode]
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:09.563 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:09.562 SET FEATURES [Enable SATA feature]
Error 46111 [22] occurred at disk power-on lifetime: 166 hours (6 days + 22 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
04 -- 61 00 45 00 00 00 00 00 00 a0 00 Device Fault; Error: ABRT
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
ef 00 03 00 45 00 00 00 00 00 00 a0 08 00:00:09.563 SET FEATURES [Set transfer mode]
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:09.563 READ LOG EXT
ef 00 10 00 02 00 00 00 00 00 00 a0 08 00:00:09.562 SET FEATURES [Enable SATA feature]
ec 00 00 00 00 00 00 00 00 00 00 a0 08 00:00:09.562 IDENTIFY DEVICE
2f 00 00 00 01 00 00 00 00 00 00 a0 08 00:00:04.113 READ LOG EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 152 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
Device State: Active (0)
Current Temperature: 34 Celsius
Power Cycle Min/Max Temperature: 34/34 Celsius
Lifetime Min/Max Temperature: 20/37 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (288)
Index Estimated Time Temperature Celsius
289 2022-08-30 14:14 35 ****************
... ..( 51 skipped). .. ****************
341 2022-08-30 15:06 35 ****************
342 2022-08-30 15:07 34 ***************
... ..( 15 skipped). .. ***************
358 2022-08-30 15:23 34 ***************
359 2022-08-30 15:24 ? -
360 2022-08-30 15:25 23 ****
361 2022-08-30 15:26 ? -
362 2022-08-30 15:27 26 *******
363 2022-08-30 15:28 ? -
364 2022-08-30 15:29 26 *******
365 2022-08-30 15:30 27 ********
366 2022-08-30 15:31 28 *********
367 2022-08-30 15:32 28 *********
368 2022-08-30 15:33 29 **********
369 2022-08-30 15:34 29 **********
370 2022-08-30 15:35 29 **********
371 2022-08-30 15:36 30 ***********
... ..( 2 skipped). .. ***********
374 2022-08-30 15:39 30 ***********
375 2022-08-30 15:40 31 ************
... ..( 4 skipped). .. ************
380 2022-08-30 15:45 31 ************
381 2022-08-30 15:46 32 *************
... ..( 7 skipped). .. *************
389 2022-08-30 15:54 32 *************
390 2022-08-30 15:55 33 **************
... ..( 15 skipped). .. **************
406 2022-08-30 16:11 33 **************
407 2022-08-30 16:12 34 ***************
408 2022-08-30 16:13 34 ***************
409 2022-08-30 16:14 33 **************
410 2022-08-30 16:15 33 **************
411 2022-08-30 16:16 33 **************
412 2022-08-30 16:17 34 ***************
... ..(129 skipped). .. ***************
64 2022-08-30 18:27 34 ***************
65 2022-08-30 18:28 ? -
66 2022-08-30 18:29 34 ***************
67 2022-08-30 18:30 ? -
68 2022-08-30 18:31 34 ***************
69 2022-08-30 18:32 ? -
70 2022-08-30 18:33 34 ***************
... ..( 5 skipped). .. ***************
76 2022-08-30 18:39 34 ***************
77 2022-08-30 18:40 ? -
78 2022-08-30 18:41 34 ***************
... ..( 6 skipped). .. ***************
85 2022-08-30 18:48 34 ***************
86 2022-08-30 18:49 ? -
87 2022-08-30 18:50 34 ***************
... ..( 15 skipped). .. ***************
103 2022-08-30 19:06 34 ***************
104 2022-08-30 19:07 ? -
105 2022-08-30 19:08 35 ****************
106 2022-08-30 19:09 34 ***************
107 2022-08-30 19:10 34 ***************
108 2022-08-30 19:11 34 ***************
109 2022-08-30 19:12 ? -
110 2022-08-30 19:13 35 ****************
111 2022-08-30 19:14 34 ***************
... ..( 3 skipped). .. ***************
115 2022-08-30 19:18 34 ***************
116 2022-08-30 19:19 ? -
117 2022-08-30 19:20 35 ****************
118 2022-08-30 19:21 ? -
119 2022-08-30 19:22 35 ****************
120 2022-08-30 19:23 34 ***************
... ..( 2 skipped). .. ***************
123 2022-08-30 19:26 34 ***************
124 2022-08-30 19:27 ? -
125 2022-08-30 19:28 35 ****************
126 2022-08-30 19:29 ? -
127 2022-08-30 19:30 35 ****************
128 2022-08-30 19:31 34 ***************
... ..( 10 skipped). .. ***************
139 2022-08-30 19:42 34 ***************
140 2022-08-30 19:43 ? -
141 2022-08-30 19:44 34 ***************
... ..( 2 skipped). .. ***************
144 2022-08-30 19:47 34 ***************
145 2022-08-30 19:48 ? -
146 2022-08-30 19:49 34 ***************
... ..( 2 skipped). .. ***************
149 2022-08-30 19:52 34 ***************
150 2022-08-30 19:53 ? -
151 2022-08-30 19:54 34 ***************
152 2022-08-30 19:55 34 ***************
153 2022-08-30 19:56 ? -
154 2022-08-30 19:57 34 ***************
... ..( 16 skipped). .. ***************
171 2022-08-30 20:14 34 ***************
172 2022-08-30 20:15 35 ****************
173 2022-08-30 20:16 34 ***************
... ..( 14 skipped). .. ***************
188 2022-08-30 20:31 34 ***************
189 2022-08-30 20:32 ? -
190 2022-08-30 20:33 35 ****************
191 2022-08-30 20:34 ? -
192 2022-08-30 20:35 35 ****************
193 2022-08-30 20:36 34 ***************
194 2022-08-30 20:37 35 ****************
... ..( 2 skipped). .. ****************
197 2022-08-30 20:40 35 ****************
198 2022-08-30 20:41 ? -
199 2022-08-30 20:42 35 ****************
200 2022-08-30 20:43 35 ****************
201 2022-08-30 20:44 ? -
202 2022-08-30 20:45 35 ****************
203 2022-08-30 20:46 ? -
204 2022-08-30 20:47 35 ****************
205 2022-08-30 20:48 ? -
206 2022-08-30 20:49 35 ****************
207 2022-08-30 20:50 ? -
208 2022-08-30 20:51 35 ****************
209 2022-08-30 20:52 34 ***************
... ..( 3 skipped). .. ***************
213 2022-08-30 20:56 34 ***************
214 2022-08-30 20:57 ? -
215 2022-08-30 20:58 34 ***************
... ..( 5 skipped). .. ***************
221 2022-08-30 21:04 34 ***************
222 2022-08-30 21:05 ? -
223 2022-08-30 21:06 34 ***************
224 2022-08-30 21:07 34 ***************
225 2022-08-30 21:08 ? -
226 2022-08-30 21:09 34 ***************
227 2022-08-30 21:10 34 ***************
228 2022-08-30 21:11 ? -
229 2022-08-30 21:12 34 ***************
... ..( 4 skipped). .. ***************
234 2022-08-30 21:17 34 ***************
235 2022-08-30 21:18 ? -
236 2022-08-30 21:19 34 ***************
237 2022-08-30 21:20 ? -
238 2022-08-30 21:21 34 ***************
239 2022-08-30 21:22 34 ***************
240 2022-08-30 21:23 34 ***************
241 2022-08-30 21:24 ? -
242 2022-08-30 21:25 34 ***************
243 2022-08-30 21:26 34 ***************
244 2022-08-30 21:27 34 ***************
245 2022-08-30 21:28 ? -
246 2022-08-30 21:29 34 ***************
... ..( 3 skipped). .. ***************
250 2022-08-30 21:33 34 ***************
251 2022-08-30 21:34 ? -
252 2022-08-30 21:35 34 ***************
... ..( 2 skipped). .. ***************
255 2022-08-30 21:38 34 ***************
256 2022-08-30 21:39 33 **************
257 2022-08-30 21:40 ? -
258 2022-08-30 21:41 34 ***************
259 2022-08-30 21:42 34 ***************
260 2022-08-30 21:43 ? -
261 2022-08-30 21:44 34 ***************
262 2022-08-30 21:45 ? -
263 2022-08-30 21:46 34 ***************
264 2022-08-30 21:47 ? -
265 2022-08-30 21:48 34 ***************
266 2022-08-30 21:49 ? -
267 2022-08-30 21:50 34 ***************
268 2022-08-30 21:51 ? -
269 2022-08-30 21:52 34 ***************
... ..( 8 skipped). .. ***************
278 2022-08-30 22:01 34 ***************
279 2022-08-30 22:02 ? -
280 2022-08-30 22:03 34 ***************
281 2022-08-30 22:04 ? -
282 2022-08-30 22:05 34 ***************
283 2022-08-30 22:06 34 ***************
284 2022-08-30 22:07 34 ***************
285 2022-08-30 22:08 ? -
286 2022-08-30 22:09 34 ***************
287 2022-08-30 22:10 ? -
288 2022-08-30 22:11 34 ***************
SCT Error Recovery Control command not supported
Device Statistics (GP Log 0x04)
Page Offset Size Value Flags Description
0x01 ===== = = === == General Statistics (rev 1) ==
0x01 0x008 4 110 --- Lifetime Power-On Resets
0x01 0x010 4 166 --- Power-on Hours
0x01 0x018 6 1484560469 --- Logical Sectors Written
0x01 0x020 6 10232676 --- Number of Write Commands
0x01 0x028 6 742464778 --- Logical Sectors Read
0x01 0x030 6 6013459 --- Number of Read Commands
0x01 0x038 6 597600000 --- Date and Time TimeStamp
0x03 ===== = = === == Rotating Media Statistics (rev 1) ==
0x03 0x008 4 163 --- Spindle Motor Power-on Hours
0x03 0x010 4 143 --- Head Flying Hours
0x03 0x018 4 116 --- Head Load Events
0x03 0x020 4 12072 --- Number of Reallocated Logical Sectors
0x03 0x028 4 75012 --- Read Recovery Attempts
0x03 0x030 4 0 --- Number of Mechanical Start Failures
0x03 0x038 4 15288 --- Number of Realloc. Candidate Logical Sectors
0x03 0x040 4 102 --- Number of High Priority Unload Events
0x04 ===== = = === == General Errors Statistics (rev 1) ==
0x04 0x008 4 0 --- Number of Reported Uncorrectable Errors
0x04 0x010 4 225 --- Resets Between Cmd Acceptance and Completion
0x05 ===== = = === == Temperature Statistics (rev 1) ==
0x05 0x008 1 34 --- Current Temperature
0x05 0x010 1 34 --- Average Short Term Temperature
0x05 0x018 1 - --- Average Long Term Temperature
0x05 0x020 1 37 --- Highest Temperature
0x05 0x028 1 26 --- Lowest Temperature
0x05 0x030 1 34 --- Highest Average Short Term Temperature
0x05 0x038 1 30 --- Lowest Average Short Term Temperature
0x05 0x040 1 - --- Highest Average Long Term Temperature
0x05 0x048 1 - --- Lowest Average Long Term Temperature
0x05 0x050 4 0 --- Time in Over-Temperature
0x05 0x058 1 60 --- Specified Maximum Operating Temperature
0x05 0x060 4 0 --- Time in Under-Temperature
0x05 0x068 1 0 --- Specified Minimum Operating Temperature
0x06 ===== = = === == Transport Statistics (rev 1) ==
0x06 0x008 4 2078 --- Number of Hardware Resets
0x06 0x010 4 1429 --- Number of ASR Events
0x06 0x018 4 0 --- Number of Interface CRC Errors
0xff ===== = = === == Vendor Specific Statistics (rev 1) ==
0xff 0x008 7 0 --- Vendor Specific
0xff 0x010 7 0 --- Vendor Specific
0xff 0x018 7 0 --- Vendor Specific
|||_ C monitored condition met
||__ D supports DSN
|___ N normalized value
Pending Defects log (GP Log 0x0c)
Index LBA Hours
0 666675392 -
1 666675393 -
2 666675394 -
3 666675395 -
4 666675396 -
5 666675397 -
6 666675398 -
7 666675399 -
8 666675400 -
9 666675401 -
10 666675402 -
11 666675403 -
12 666675404 -
13 666675405 -
14 666675406 -
15 666675407 -
16 666806032 -
17 666806033 -
18 666806034 -
19 666806035 -
20 666806036 -
21 666806037 -
22 666806038 -
23 666806039 -
24 666806040 -
25 666806041 -
26 666806042 -
27 666806043 -
28 666806044 -
29 666806045 -
30 666806046 -
... (497 entries not shown)
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 0 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 1 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000d 2 0 Non-CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 73 Vendor specific
well there are some errors …
you could try to completely reset the ssd, here is a link on arch on how to do it:
https://wiki.archlinux.org/title/Solid_state_drive/Memory_cell_clearing
ill give it a shot, thanks
wait you dont have an ssd its a normal hdd … so forget about the reseting
oh yeah, is there anything similar for a hdd
not that im aware off
can you delete the whole disk? in kde partition manager there is o option to ‘delete’ - does it fails too?
also try to installing windows on it, if you would be able to do that, then theres probably a bios setting/option that messes things up in linux
apparently my usb isnt big enough to install windows, its also now saying there is no partition table again and its not letting me make a new one